Proper Recording Level; Rec Mute And Rec Pause Button; Dubbing - Marantz SD4050 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

PROPER RECORDING LEVEL

A too high recording level can saturate the tape and cause distortion.
On the other hand, if the recording level is set too low, soft passages
will be marked by residual noise. A proper recording level is the
single most important factor for making well balanced recordings.
Guideline for maximum recording level
q (Normal)
TYPE
TYPE w (High position)
TYPE r (Metal)

REC MUTE AND REC PAUSE BUTTON

1. To record a 4-second blank section during recording:
Press the REC MUTE button. A 4-second blank will be recorded
and the deck will enter the recording Pause mode.
2. To record a 4-second blank section during the recording Pause
mode:
Press the REC MUTE button from the recording Pause mode. A 4
second blank will be recorded and the deck will enter the
recording Pause mode again.

DUBBING

(from deck A to deck B)
¼ Switch on the amplifier or receiver.
¼ Set the Tape Monitor or Function switch on your amplifier or
receiver to the TAPE/TAPE monitor position.
DOLBY NR
C
B
OFF
TIMER
REC
OFF
PLAY
REV. MODE
AUTO TAPE SELECT/HIGH SPEED DUBBING
CCONT. PLAY
POWER
ON/OFF
e
q
1. Press the POWER switch q to the ON (
2. Load the cassette tape to be played on deck A and the one to be
recorded in deck B w.
position of the REV MODE switch e.
3. Select the
REV. MODE
Reverse mode
Dubbing is performed only for one side.
The decks stop when either deck A or B
reaches the end of the tape.
The tape direction is reversed on each deck
when they reach the end of the tape.
or
(This is convenient for dubbing to a tape with
a different length.)
All manuals and user guides at all-guides.com
0 dB level on peaks
1 dB level on peaks
3 dB level on peaks
w
DOUBLE CASSETTE DECK SD4050
COUNTER
RESET
DUBBING SPEED
SYNC REV
NORMAL
HIGH
AUTO REVERSE
STOP
PLAY
EJECT
A
PLAY
r
) position.
Operation
Note:
The optimum recording level differs depending on the program
source and the type of tape used.
3. To cancel recording of blank space:
Press the PAUSE (
canceled and the deck enters the recording Pause mode.
4. To extend the blank section with another 4 seconds or more:
Simply press the REC MUTE button and the blank section will be
increased with another 4 seconds.
t
w
COUNTER
RESET
REC LEVEL
RECORD
PAUSE
REC MUTE
STOP
PLAY
MIN
MAX
PHONES
EJECT
B
PITCH
REC/PLAY
CONTROL
+
y
u
4. To being normal speed dubbing, press the DUBBING SPEED
HIGH button r. The NORM DUB indicator will light at this timee.
The HIGH DUB indicator will light at this time.
5. To stop dubbing, press the STOP (
B.
¼ When dubbing, the recording level and the Dolby NR recording
will be the same as those of the playback tape, regardless of
the positions of the REC LEVEL control and the DOLBY NR
button.
¼ When listening to the playback sound suring normal speed
dubbing, the DOLBY NR switch remains off even if it is
pressed.
¼ Operation using the REC MUTE and PAUSE (
u of deck B is permitted during normal speed dubbing.
10
) button. Blank space recording will be
AUTO REVERSE
AUTO TAPE SELECT/HIGH SPEED DUBBING
) button t of deck A or deck
) buttons y,

Publicité

Chapitres

Table des Matières
loading

Table des Matières