Specifications; Assembly; Operational Information; Maintenance - MrHeater MH165FAET Manuel

SPECIFICATIONS

Model: MH165FAET
Heat Output BTU/WATTS 5118/1500
Airflow (CFM) 200
Electrical Supply 120Vac
Thermostat 32°F - 185°F
Power Cord 6Ê POWER CABLE INCLUDED 6Ê POWER CABLE INCLUDED
Dimensions: (L‰xW‰xH‰) 13.18‰x12.2‰x13.97‰ 14.37‰x13.77‰x16.14‰
Weight (lbs.) 9.6 LBS.
Clearance to Combustibles
Outlet (M) 6Ê (1.8M)
Rear (M) 2Ê (.6M)
Top (M) 2Ê (.6M)
Bottom (M) Use only on non-combustible flooring

Assembly

• Remove the heater and all of the packaging material from
the box.
• Check all of the packing material for loose parts and set
aside.
• Thoroughly inspect the heater for damage. If any is found
do not contact the place of purchase. Please call the
Manufacturer at 800-251-0001.

Operational Information

The Mr. Heater Electric forced air heaters are designed to be
used by professionals.
Heat is created by electric current passing through coiled metal
elements bringing them up to very high temperatures. The fan then
passes room air over the hot elements exchanging cold air for warm.
The air moving over the coils keeps them from reaching
temperatures that are not safe for the normal operation of
the heater. However it is important to keep all combustible
materials and any objects that may be sucked into the fan
blades at a safe distance (please refer to the specification table
for appropriate clearances). Make sure that the fan blades
remain unobstructed at all times. Keep unit clean and dust free.
Do not block unit intake or exhaust at any time.
These units are designed to be used only with the cord and
plug supplied with the unit. Do not use any plug other than the
one supplied by the manufacturer. For information on which
receptacle is appropriate, Refer to Figure 1 and find the diagram
that corresponds to your heater.
If damage has occurred please refer to the parts listing in this
manual and contact the manufacturer for a replacement.
WARNING: Outlet must be properly grounded, failure to do
so may result in electric shock or property damage.
WARNING: Always plug heaters directly into a wall outlet/
receptacle. Never use with an extension cord or re-locatable
power tap (outlet/power strip).
Starting Instructions
1. Place the heater on a stable and level surface. Insure clearance to
combustibles are observed (See clearances in the specification table).
2. Turn thermostat counter-clockwise to lowest setting.
3. Plug the heater into a properly grounded outlet.
4 Rotate the power knob to the heating position. These units are
equipped with a fan only option for circulating air. For heating be
sure to rotate the knob to the appropriate setting.
Mr. Heater Forced-Air Electric Construction Heater
MH360FAET
Figure 1
12286/3600
325
240Vac
32°F - 185°F
12 LBS.
6Ê (1.8M)
2Ê (.6M)
2Ê (.6M)
Operating Instructions and OwnerÊs Manual
3
5. Turn thermostat knob up (clockwise) to the desired setting.
6. The Heating element and fan will remain on until the temperature
setting is reached. The unit will cycle on and off as needed.
MH165FAET
NEMA 5-15R
To Stop Heating
1. Rotate the thermostat knob to the lowest position.
2. Flip the power switch into the „off‰ position.
3. Disconnect plug from power supply.
NOTE: This heater is equipped with an overheat limit switch
which may cause the heater to stop. This is indicated by a visual
alarm when the power switch is in the „ON‰ position and the
„fault‰ light comes on. Check and remove the cause of the
overheating before restarting. This can take up to 10 minuets to
cool before it can be restarted.

Maintenance

WARNING:
Never attempt to service the heater while the unit is hot,
In use, or plugged in. Only qualified service technicians
should service these units.
• Thoroughly inspect the unit prior to use.
• Keep heater clean and free of dust and debris.
• The use of an air compressor can be used to blow out the dust
from the heater case. Be sure to only use moderate air pressure
as to not damage any internal components.
• A soft dry cloth should be used for cleaning of outer shell
and handle.
• The fan motor is sealed and does not need to be lubricated.
Storage
When not in use, the heater must be disconnected from power
source, dusted off and the cord should be loosely wound
around the handle.
For service :
Please call Toll-Free 800-251-0001 www.mrheater.com
Our office hours are 8:00 AM – 5:00 PM, EST, Monday through
Friday. Please include the model number, date of purchase, and
description of problem in all communication.
CONTROL
OVERHEAT LIGHT
THERMOSTAT KNOB
MH360FAET
NEMA 6-20R
FAN
ONLY
OFF
HEAT