Installing And Removing The Battery Pack - DeWalt DCD997 Guide D'utilisation

D WALT Tool Connect™
e

WARNING: To reduce the risk of injury, remove
accessories from the tool chuck before any Tool
Connect™ interaction.
NOTICE: Always check the tool configuration prior
to use. If you are unsure of the current configuration,
press the mode button 14
to the Home setting as described on the label and
this manual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://
www.bluetooth.com/Pages/Bluetooth-Smart-Devices-List.
aspx)
D WALT Tool Connect™ is an application for your smart
e
device (such as a smart phone or tablet) that connects the
device to your tool to allow you to configure specific tool
functions. Refer to Mode Selector.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use
of such marks by D WALT is under license. Other trademarks
e
and trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D WALT Tool Connect™ application at:
e
• Follow the instructions in the app to create your Tool
Connect™ account.
• On the Home screen of the app, select "+ Tool" to begin
the process of adding your tool to the app.
• To connect your tool with the D
app, at the appropriate screen, press the mode selector
button for 3–5 seconds, then wait for the tool to
14
connect. The tool can only be connected to one Tool
Connect™ account at a time.
• Once the tool has been connected, you can confirm that
you would like to register the product.
For more information on D WALT Tool Connect™
e
functionality and features, please call 1–800–4-D
(1–800–433–9258), visit www.D WALT.com or view
e
the FAQ page and help screens located inside the
mobile application.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your
local D WALT service center. Do not attempt to replace the
e
coin cell battery yourself.

WARNING: Danger of explosion if battery is
incorrectly replaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/
button cell battery. If the coin/button cell battery is
swallowed, it can cause severe internal burns in just
2 hours and can lead to death.
All manuals and user guides at all-guides.com
(Fig. J) to set the tool
OPERATION


Installing and Removing the Battery Pack

WALT Tool Connect™
e
(Fig. K)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
WALT
e
To remove the battery pack from the tool, press the release
button
handle. Insert it into the charger as described in the charger
section of this manual.
• Keep new and used batteries away from children.
If the battery compartment does not close
securely, stop using the product and keep it away
from children.
• If you think batteries might have been swallowed
or placed inside any part of the body, seek
immediate medical attention.
• If the coin cell battery contents come into contact
with the skin, immediately wash area with mild
soap and water. If coin cell battery liquid gets
into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte is
composed of an organic solvent and lithium salts.
• Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recycling facility.
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury. Exception—Tool
Connect™ functions and mode adjustments require
battery to be installed.
NOTICE: Always check the tool configuration prior
to use. If you are unsure of the current configuration,
press the mode button 14 (Fig. J) to set the tool
to the Home setting as described on the label and
this manual.
into the tool handle, align the
11
and firmly pull the battery pack out of the tool
10
Fig. K
11
10
English
11