BWT AQA drink Pro 20 CAS Instructions De Montage Et De Service D'origine page 14

4.1 WARRANTY AND DISCLAIMER
The AQA drink Pro 20 water dispenser has a 2-year warranty. The specified information and rec-
ommendations, as well as the local drinking water and waste disposal regulations valid for the
application in question, must be complied with. All information and instructions in these installa-
tion and operating instructions take account of applicable standards and regulations, the state
of the art, as well as our many years of knowledge and experience. Illustrations in this manual are
intended to provide a basic understanding and may vary from the actual design of the device.
No claims may be derived from this. BWT can accept no liability for damage or consequential
damage due to:
» non-compliance with the information given in these installation and operating instructions;
» use for purposes other than the intended purpose;
» incorrect or faulty installation;
» incorrect commissioning, operation and maintenance;
» use of components that have not been approved;
» non-performance of the prescribed service and replacement work;
» unauthorised technical or mechanical changes or modifications.
4.2 RESPONSIBILITY OF THE OPERATING COMPANY
» The installation and operating instructions must be kept in the immediate vicinity of the de-
vice and must be accessible at all times.
» The device may only be operated in a technically correct and operationally safe condition.
» The information in these installation and operating instructions must be complied with, at all
times.
4.3 LICENCE TERMS
The installation and operating instructions are protected by copyright. The transfer of these
instructions to third parties, reproduction of any kind – including extracts – as well as the
exploitation and/or disclosure of the content are not permitted without the written consent of
the manufacturer. Any breach or infringement will result in liability for damages. We reserve the
right to assert further claims.
With the acquisition of the AQA drink Pro 20 water dispenser, the user receives an exclusive,
nontransferable right to use the software installed by the manufacturer.
4.4 QUALIFIED PERSONNEL
Only trained personnel and staff may install, put into operation and maintain the water dispens-
er. The trained person has been informed of the tasks entrusted to him/her, and of possible
dangers in the event of improper use or behaviour. Trained persons are in a position to install,
put into operation and maintain the device on due to of their technical training, knowledge and
experience as well as knowledge of the applicable regulations.
Define clear guidelines for the relevant responsibility for operation, installation, maintenance
and repairs.
26
All manuals and user guides at all-guides.com
The following laws must be observed while installing and operating of the system:
» Technical rules for drinking water installation.
» Ordinance relating to the quality of water intended for human consumption (drinking water
ordinance).
All delivered AQA drink Pro 20 water dispensers comply with the EU Directives 2011/65/EU
and 2015/863/EU on the restriction of the use of certain hazardous substances in electrical and
electronic equipment.
Prior to installation, read Chapter 2 "Technical data" and Chapter 4 "Operating/Safety Instruc-
tions."
Set up and operate the device in a vertical position.
Do not place the device directly against a wall. Leave a distance of at least 15 cm.
5.1 UNPACKING THE AQA DRINK PRO 20 WATER DIPENSER
Remove your device from the packaging. Check that the shipment is complete and has not been
damaged in transit. Defective parts must be replaced immediately.
5.2 PREPARING THE AQA DRINK PRO 20 WATER DISPENSER
Place the device on a level surface or on the AQA drink Pro 20 cabinet (optional).
Position the drip tray in the intended place below the water outlet.
The cabinet includes a second drip tray; this must be used in conjunction with the cabinet. The
second drip tray is connected to the wastewater tank, which is mounted in the cabinet. Con-
nect the prepared plug in the cabinet to the water level sensor mounted in the wastewater tank.
5.3 INSTALLING THE FILTER
Observe the installation and operating instructions for the installation of filters. We recommend
using BWT filters, which are ideally suited for the device.
5.4 CONNECTING THE WATER AND FILLING THIS SYSTEM
When installing accessories (hoses, connection kits), observe the installation dimensions and
bending radii.
A new connection kit (connection pieces, seals and hoses) must be used to connect the device
to the water supply. Do not use a used connection kit!
To connect the device, use only hoses that comply with DVGW W 543 (DVGW – German Tech-
nical and Scientific Association for Gas and Water).
27