Charging The Battery; Fitting The Battery; Working With The Power Tool - Hilti AG 125-A22 Mode D'emploi

6.2 Charging the battery

DANGER
Use exclusively the specified Hilti batteries and Hilti
battery chargers listed under "Accessories".
6.2.1 Charging a new battery for the first time
Charge the battery fully before using it for the first time.
6.2.2 Charging a previously used battery
Ensure that the outer surfaces of the battery are clean
and dry before inserting it in the corresponding charger.
Read the operating instructions for the charger for further
information about the charging procedure.
Lithium-ion battery packs are ready to use at any time,
even when only partially charged. Charging progress
is indicated by the LED display (see charger operating
instructions).

6.3 Fitting the battery

CAUTION
Check that the power tool is switched off and the
switch interlock activated before fitting the battery.
Use only the Hilti batteries approved for use with this
power tool.
CAUTION
Before inserting the battery in the power tool, check
to ensure that the battery terminals and the contacts
in the power tool are free from foreign objects.
1. Push the battery into the power tool from the rear as
far as it will go and until it is heard to engage with a
double click.
CAUTION If it is not fitted securely, the battery
2.
could fall out while you are working with the tool.
CAUTION A falling battery may present a risk of
injury to yourself and others.
Before beginning the work, check that the battery is
fitted securely to the tool.
6.4 Removing the battery from the power tool
1. Press both release buttons and hold them in this
position.
2. Pull the battery out of the power tool to the rear.
6.5 Transport and storage of batteries
Pull the battery out of the locked position (working pos-
ition) and move it into the first click-stop position (trans-
port position).
If you disconnect a battery from the power tool for trans-
port or storage, make sure that the battery contacts are
not short-circuited. Remove loose metal parts such as
screws, nails, clamps, loose screwdriving bits, wires or
metal swarf from the case, toolbox or transport container,
All manuals and user guides at all-guides.com
or prevent these parts from coming into contact with the
battery.
Observe national and international transport regulations
when shipping batteries (transportation by road, rail, sea
or air).
6.6 Fitting the side handle
WARNING
The side handle must be fitted for all types of work.
The side handle may be screwed onto the tool on the
right or left.

6.7 Working with the power tool

DANGER
Remove the battery from the power tool before mak-
ing any adjustments, before changing accessories
and before storing the power tool. Such preventive
safety measures reduce the risk of starting the tool acci-
dentally.
CAUTION
Wear gloves when fitting or removing parts, when
making adjustments or when remedying malfunc-
tions.
Take care to ensure that the closed side of the guard is
always positioned toward the operator's body.
Adjust the position of the guard to suit the requirements
of the work being done.
Read the instructions for fitting the corresponding guard.
6.7.1 Fitting and removing the guard or guard with
NOTE
The guard is equipped with locating lugs that ensure only
guards of a type suitable for use with the power tool can
be fitted. The locating lugs of the guard fit into the guard
mount on the power tool.
1.
2.
3.
4.
6.7.1.1 Adjusting the guard
1.
6.7.2 Fitting the cutting guard 7 8
NOTE
Take care to ensure that the on / off switch is freely
accessible and operable at all times.
cover plate 6
Fit the guard onto the drive spindle collar so that the
two triangular marks on the guard and on the power
tool are in alignment.
Push the guard onto the drive spindle collar; press
the guard release button.
Rotate the guard until it engages and the guard
release button jumps back into its original position.
To remove the guard from the power tool, follow the
instructions for fitting the guard but carry out the
steps in the reverse order.
Press the guard release button and then rotate the
guard until it engages in the desired position.
en
27