AERMEC VMF-E4X Manuel D'installation page 9

CHANGE TO USER PARAMETERS
The VMF-E4X panel has parameters defined as "User" that are used to select the speed of the inverter fan coils when the latter operates in
modes V1, V2, V3 and to set the position of the flaps for FCL fan coils with GLFM grille.
To access the "User" menu area, press the Mode/Select key (
OFF
SET
+
SET OFF
+
AUTO
AUTO
AUX
AUX
MODE
MODE SELECT
SELECT
Parameter symbol SET OFF
+ OFF
SET
+
AUTO
AUTO
AUX
OFF
SET
AUX
+
SET OFF
SET OFF
+
+
MODE
AUTO
MODE
SELECT
SELECT
AUTO
AUTO
AUX
AUX
AUX
OFF
SET
+
SET MODE MODE OFF MODE
+ SELECT SELECT
SELECT
AUTO
AUTO
AUX
OFF
SET
AUX
+
OFF
SET
SET OFF
+
+
MODE
AUTO
MODE SELECT
SELECT
AUTO
AUTO
AUX
AUX
AUX
MODE MODE
MODE
SELECT SELECT
SELECT
OFF
SET
+
SET OFF
SET OFF
+
+
AUTO
AUTO
AUTO
AUX
AUX
AUX
MODE MODE MODE
SELECT SELECT
SELECT
OFF
SET
+
AUTO
AUX
MODE
SELECT
NB: The FLP (Flaps position) parameter allows to select the position of the flaps in the motorized GLFxxM grille, if the value is between 0 and
100% the FLP parameter represents the position of the deflector, if the value selected is 101 it activates the SWING operating mode (conti-
nuous movement of the 4 deflectors in the grille).
CHANGE VISUALIZATION PARAMETERS
The E4X panel, in order to meet the needs of the building automation, includes parameters relating to the possibility of displaying the actual
setpoint and modifying the display of the operating status if the thermostat to which it is connected is subject to force commands by a BMS.
external. In addition to this sub-menu there is the parameter for selecting the temparature measuring unit: ° C / ° F. To access this submenu,
OFF
SET
+
SET OFF
+
press the UP and DOWN keys simultaneously (see table below) for a few seconds. AUTO
AUTO
AUX
AUX
MODE
MODE
SELECT
SELECT
Parameter symbol
OFF
SET
SET + OFF
+
SET AUTO OFF
SET OFF
AUTO +
+
AUX
AUX
AUTO
AUTO
AUX
AUX
MODE
MODE
SELECT
SELECT
MODE MODE
SELECT SELECT
SET OFF
+ OFF
SET
+
AUTO
SET OFF
OFF
SET AUTO
+
+
AUX
AUX
AUTO
AUTO
AUX
AUX
MODE
MODE
SELECT
SELECT
MODE MODE
SELECT SELECT
OFF
SET
SET OFF
+
+
AUTO
AUTO
AUX
AUX
MODE
MODE
SELECT SELECT
SET
+
AUTO
OFF
SET
+
AUTO
AUX
MODE
OFF
SET
SELECT
+
AUTO
AUX
MODE
OFF
SET
SELECT
+
AUTO
AUX
MODE
SELECT
OFF
SET
+
AUTO
AUX
MODE
SELECT
OFF
SET
+
AUTO
AUX
MODE
SELECT
OFF
SET
+
AUTO
AUX
MODE
SELECT
OFF
AUX
) for about 5 seconds.
MODE
SELECT
Change parameter value
OFF
SET
+
AUTO
AUX
MODE
SELECT
OFF
SET
+
AUTO
AUX
MODE
SELECT
OFF
SET
+
AUTO
AUX
MODE
SELECT
OFF
SET
+
AUTO
AUX
MODE
SELECT
Change parameter value
Parametro per la correzione da apportare alla lettura sonda: -5°C ÷ 5°C
Abilitazione a modificare la visualizzazione del modo di funzionamento da supervisione:
Set point display mode if an external supervisor is present:
AVMFE4XLJ-0821 - 6795769_03
Fan Speed in modeV1
(range value 5÷34 %)
Fan Speed in mode V2
(range value 33÷67 %)
Fan Speed in mode V3
(range value 67÷100 %)
Flaps position (range value 0 ÷ 101 %)
With value 101, SWING mode is activated!
Temperature unit selection:
0 → °C
1 ← °F
0 → not enabled
1 ← enabled
0 → deviation
1 ← actual setpoint
9