Tonon Forty F221546 Serie Manuel page 6

ASSEMBLY INSTRUCTIONS for the installer and the user
Read these instructions carefully before starting any assembly operation.
The radiator complies with the directives 2006/95/CEE, 89/336/CEE, 2005/32/CEE and the norms EN 60335-2-43:2003 +
A1:2006 + A2:2008; EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008; EN 62233:2008.
1 - All the installation and maintenance operations must be carried out by qualified personnel.
This towel heating can't use for the person (including the children) whose physical , sensory or mental capabilities or lack of
experience and knowledge .Prevents them from using the appliance safely without supervision or instruction . It's necessary to
guard the children don't playing with the appliance.
2 - The manufacturer declines all responsibility in the event of assembly which does not respect these instructions, or the use of
non original material or accessories.
3 - The radiator is filled with a special liquid. Repairs which require the opening of the tank must be carried out exclusively by the
manufacturer or his technical assistance service which must be contacted in the event of leakage of liquid. If this heating
appliance is to be scrapped, the regulations on the disposal of the heating fluid
must be complied with.
4 - If the cable become damaged it must be replaced by the manufacturer, by the authorized assistance service or by a technically
qualified person in order to avoid all risks.
5 - The heating appliance must not be placed under an electric socket but in such a position that the switches and other control
devices cannot be touched by a person who is in the bath tub or under the shower.
6 – WARNING: in order to avoid a hazard for very young children, this appliance should be installed so that the lo west heated rail
is at least 600mm above the floor.
7 - During operation, it is normal for the first pipes at the bottom and the last one at the top not to be heated (the lower part to
facilitate the natural circulation of the fluid, the pipe at the top is empty to allow the expansion of the fluid when heated).
8 - Avoid using the radiator in the presence of gas, explosives or inflammable products.
ELECTRICAL CONNECTION
Cables: grey (or blue) = neutral, brown = phase, black = pilot wire (only for mod. B – see fig.4).
Power supply for single-phase current 230V ~ 50 Hz.
The connection must be made in compliance with the regulations in force; before connecting the electric resistance to the line,
check the voltage and power values indicated on the data plate.
For the models not equipped with a plug (mod. B – fig. 4) – Specific for the French market
The electric supply circuit of the radiator must be protected by a 30 mA differential switch. The opening distance between the
contacts must be greater than 3 mm. Moreover, the circuit must be easily accessible.
The pilot wire (black) must be insulated, if it is not used.
Power On / Stand-by mode
Press 'ON/OFF' button (fig.1) to turn the appliance ON or in Stand-by mode.
When On, the bottom area of the display shows the current time, on the top the temperature setting is displayed.
COMFORT and NIGHT temperature setting
Two different levels of temperature can be set:
-COMFORT TEMPERATURE is the temperature setting for 'Chrono', 'Fil Pilote' and 'Comfort' modes;
-NIGHT TEMPERATURE is the temperature setting for the 'Night' and 'Chrono' mode.
In each mode the required temperature can be set by pressing the [+] and [-] buttons (fig.1)
IMPORTANT!
Night Temperature has always to be lower or equal to the Comfort Temperature, and the priority is assigned to the Comfort
Temperature. For this reason Night Temperature can be set in the range 7° C ÷ Comfort Temperature, on the contrary the
Comfort Temperature can be set within the whole range 7°÷32° C (and in case of a value lower than the Night Temperature, the
system re-set automatically the new Night Temperature at the same value of Comfort Temperature).