Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Setting the regional TV system
format
INPUT1 and INPUT2 are compatible with a number of TV
system formats used around the world, which are
automatically detected by this unit.
Normally "COLOR SYSTEM:AUTO" should be selected
for automatic detection. However, some video signals are
dubbed over or in certain conditions may not be displayed
properly (loss of color, etc.) by this setting. In this case,
change the setting according to the input signal.
Note
Setting the TV system format is required for both INPUT1 and
INPUT2. Setting assignment and exclusive use according to the
TV system format of your input signal will enable prompt
processing of signals and reduction of time for input selection
and possible errors in detecting signals.
1
Press MENU to display the menu screen.
The menu screen appears.
2
Press 5/∞ to select SET UP, then press SET.
M A I N
M E N U
P I C T U R E
S C R E E N
A L L
R E S E T
P OW E R
S A V E
S E T
U P
M E N U : M E N U
O F F
: S E L E C T
3
Press 5/∞ to select COLOR SYSTEM.
S E T
U P
N
T E R M I
A L
C O L
O R
S
Y S T E
S C
A
R
T
I N P U T
H I
G
H
C
O
N T R A
E X I
T
: S
E
L E C T
4
Press SET repeatedly until the appropriate setting
appears.
Each time SET is pressed, the settings change in the
following order.
3 AUTO
3 NTSC
4.43 NTSC 2
5
When the setup is finished, press MENU to exit
the menu screen.
S E T : N E
X T
: S C A
R T
M
: A U T
O
: A U T
O
T : O F
S
F
S
E
T
:
C
H
A
N
G
E
3 PAL
SECAM 2
Display Panel Adjustments
Viewing in a bright location
(HIGH CONTRAST)
When viewing a picture in a bright location, setting this
mode to "ON" will enable you to obtain a clear video
image.
• Set this mode to "OFF" when not viewing in a bright
location.
1
Press MENU to display the menu screen.
The menu screen appears.
2
Press 5/∞ to select SET UP, then press SET.
M A I N
M E N U
P I C T U R E
S C R E E N
A L L
R E S E T
P OW E R
S A V E
S E T
U P
M E N U : M E N U
O F F
: S E L E C T
S E T : N E
3
Press 5/∞ to select HIGH CONTRAST.
S E T
U P
T E R M I
N
A L
C O L
O R
S
Y S T E
M
S C
A
R
T
I N P U T
H I
G
H
C
O
N T R A
S
E X I
T
: S
E
L E C T
S
When viewing an image from INPUT 3 or INPUT 4,
the following screen is displayed.
S E T
U P
T E R
M I
N
A
L
: B N C
S E T T I
N G
: V I D
: C O
S I
G
N A
L
C L A M P
: M O D
H I
G
H
C
O
N T R A
E X I
T
: S
E
L E C T
4
Press SET to set the mode to "ON".
"OFF" is set when this unit is shipped from the
factory. Each time SET is pressed, the settings
change in the following order.
3 ON
OFF 2
5
When the setup is finished, press MENU to exit
the menu screen.
Note
HIGH CONTRAST setting is possible only when selecting the
video input signal from a connected video component.
X T
: S C A
R T
: A U T
O
: A U T
O
T : O F
F
E
T
:
C
H
A
N
G
E
E O
M
P O
N
E N
T 2
E 2
T : O F
S
F
S
E
T
:
C
H
A
N
G
E
23
<ARE1351> En
Publicité
Chapitres
Table des Matières
Dépannage
