Manuels Connexes pour Fantini Rubinetti EXTERNAL PARTS G872BU
Sommaire des Matières pour Fantini Rubinetti EXTERNAL PARTS G872BU
- Page 1 EXTERNAL PARTS / Instructions De Montage / Instrucciones Instructions G872BU ART.
-
Page 2: Necessary Tools
NECESSARY TOOLS - OUTILS NÉCESSAIRES - HERRAMIENTAS NECESARIAS 17mm 2 mm 30mm TECHINCAL DETAILS - DONNÉES TECHNIQUES - DATOS TÉCNICOS Minimum pressure Pression minimum Pression mínima 1 BAR Minimum pressure Pression maximum Pression máxima 10 BAR Reccomended working pressure Pression optimale de service Pression de trab. - Page 3 TECHINCAL DETAILS - DONNÉES TECHNIQUES - DATOS TÉCNICOS If water pressure is above 5 bar, it is advisable to install a flow restrictor upstream of the water supply to avoid vibrations and regulate temperature. Si la pression de l’ e au est supérieure à 5 bar, il est recommandé d’installer un réducteur de pression en amont de l’alimentation afin d’...
-
Page 4: Pre-Installation
PRE-INSTALLATION - PRÉ-INSTALLATION - PREINSTALCIÓN G872BU+D331AU G872BU+D372AU 11-3/4" 11-3/4" 5-1/8" 5-1/8" 3-3/8" 3-3/8" 3-1/4" 3-3/8" 3-3/8" 3-1/4" 2-7/8" 11" 11" 2-7/8" 5-1/8" 2-1/8" 5-1/8" 2-1/8" 1/2" NPT 1/2" NPT ↑ ← 1-1/8" 1-1/8" ↑ ↑ 3/4" NPT 3/4" NPT 1-5/8" ↓... -
Page 5: Installation - Instalación
INSTALLATION - INSTALLATION - INSTALACIÓN... - Page 6 INSTALLATION - INSTALLATION - INSTALACIÓN Edge of the tiling Fil revetement Borde revestimiento Edge of the tiling Fil revetement Borde revestimiento A÷B A÷B >0”25⁄32 0”5⁄32÷0”25⁄32 mm If the distance is greater than 0”25/32 continue from page. 11 Figure 1. Si la distance est supérieure à 0”25/32, continuez à partir de la page. 11 Graphique 1.
- Page 7 INSTALLATION - INSTALLATION - INSTALACIÓN min 0”...
- Page 8 INSTALLATION - INSTALLATION - INSTALACIÓN 2 mm...
- Page 9 INSTALLATION - INSTALLATION - INSTALACIÓN • Measure the distance “A” between the plate and the handle • Mesurer la distance “A” entre la plaque et la poignée • Medir la distancia “A” entre la placa y el mango • Cut the adapter by removing the measure “A” previously measured •...
- Page 10 INSTALLATION - INSTALLATION - INSTALACIÓN 21 - Art. D372A 22 - Art. D373A...
- Page 11 MOUNTING EXTENSION - MONTAGE RALLONGES - MONTAJE DE PROLONOGACIONES • Continue the installation from p. 7 figure 5. • Continuez l’installation à partir de la p. 7 figure 5. • Continúe con la instalación desde la pág. 7 Figura 5.
-
Page 12: Cartridge Replacement
CARTRIDGE REPLACEMENT - REPLACEMENT DE LA CARTOUCHE - SOSTITUTION DEL CARTUCHO... - Page 13 CARTRIDGE REPLACEMENT - REPLACEMENT DE LA CARTOUCHE - SOSTITUTION DEL CARTUCHO • Replace following the instructions in reverse order (8-7-6-5-4-3-2-1). • Re-installer au contraire du procédé (8-7-6-5-4-3-2-1). • Colocar según el procedimiento inverso (8-7-6-5-4-3-2-1).
- Page 14 DIVERTER REPLACEMENT / REMPLACEMENT DE INVERSEUR / SUSTITUCION DEL DISTRIBUDOR 17 mm...
- Page 15 DIVERTER REPLACEMENT / REMPLACEMENT DE INVERSEUR / SUSTITUCION DEL DISTRIBUDOR • Replace following the instructions in reverse order (7-6-5-4-3-2-1). • Re-installer au contraire du procédé (7-6-5-4-3-2-1). • Colocar según el procedimiento inverso (7-6-5-4-3-2-1).
- Page 16 Fratelli Fantini Spa via Buonarroti, 4 Pella (NO) Italia T +39 0322 918411 r.a. F +39 0322 969530 fantini@fantini.it www.fantini.it...