Unpacking; Installation - Scheppach CJS254-20ProS Traduction Des Instructions D'origine

Noise output in dB
Sound power level L
WA
Sound pressure level L
pA
Uncertainty K
wa/pA
Vibration value
Vibration
ah
Uncertainty
Kh

7. Unpacking

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage. Inform the transport agent immediately of
any faults. Later complaints cannot be considered.
• If possible, store the packaging until the warranty
period has expired.
• Familiarize yourself with the machine with the help
of the operating instructions manual before using it.
• Use only original parts for accessories as well as
consumables and spare parts. Spare parts can be
obtained from your scheppach retailer.
• Please quote our article numbers as well as type
and production year in all your orders.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!

8. Installation

Note:
Use a suitable coolant, e.g. cutting oil. This improves
the endurance and increases the service life of the
metal saw blade.
Saw blades are available which have been optimal-
ly designed for particular tasks. You can use any of
these saw blades provided they have the correct
shank fitting (single lug shank).
Mounting / replacing saw blades
Warning !
Pull the mains plug out of the socket before you carry
out any task on the device, otherwise there may be
risk of injury.
• Turn the quick-release chuck (14) and hold it in the
turned position.
• Press the selected saw blade (10) up to the stop in
the quick-release chuck (14). The saw blade (10)
should then engage.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
99 dB(A) (EN ISO 3744)
88dB(A) (EN ISO 11201)
3 dB(A)
3,327 m/s²
1,5 m/s²
• The saw blade (10) must lie in the guide roller (9).
• Release the quick-release chuck (14). The chuck
must then return to its original position. The saw
blade (10) is then locked in place.
Attaching the guide fence
The guide fence (15) can be attached on the left or
right side of the device (see fig. A).
• Release the two locking screws of the fence guide
openings (11).
• Slide the guide fence (15) into the fence guide
openings (11).
• Re-tighten the two locking screws.
Insertion / removal of a battery pack into the ap-
pliance
Ensure that the appliance is switched off before in-
serting the battery. The insertion of a battery into an
electrical appliance that is switched on can lead to
accidents.
Inserting the rechargeable battery pack:
Move the rotation switch (2) into the middle position
(lock) and push the rechargeable battery pack (5) into
the handle until it engages.
Removing the rechargeable battery pack:
Press the release button (4) and remove the re-
chargeable battery pack.
Used batteries
If a fully recharged battery lasts for considerably
shorter operating times, the battery is used up and
needs to be replaced. Only use an OEM battery pack
replacement available from our Customer Service.
Operation
Setting the cutting angle
• Release the clamping lever (6)
• Set the cutting angle 0° / 15° / 30° / 45° (left / right)
on the base plate (7). The embossed marking for
each recessed line indicates the cutting angle set-
ting. The housing has a stop pin which must en-
gage in the appropriate recessed line.
• Tighten the clamping lever (6).
Setting the speed
• Set the desired speed using the oscillation speed
setting wheel (3).
• If possible always determine the optimum setting
beforehand by carrying out a practical test.
GB | 21