Publicité
Les langues disponibles
Les langues disponibles
Lights will not go into Low Mode:
• The time delay can be set from a minimum of 30 seconds to a maximum of 30 minutes. Ensure that the time delay is set to the
desired delay and that there is no movement within the sensor's view for that time period.
• To quickly test the unit operation, enable test mode and move out of the sensor's view. Lights should fade to low mode after
5 seconds.
• If lights still do not fade to Low Mode, call 800.879.8585 for technical support.
Lights will not turn OFF:
• Cut Off time may be set to "Disable."
• Ensure that the Cut Off is set to the desired time and that there is no movement within the sensor's view for that time period when
the lights are in Low Mode.
• To quickly test the unit's operation, enable test mode and move out of the sensor's view. Lights should fade to low mode after 5
seconds and then turn OFF (if cut off is enabled) after 10 sec.
• If lights still do not turn OFF, call 800.879.8585 for technical support
False Triggering may occur if the sensor is exposed to high ambient temperature conditions and the unit is set to maximum
sensitivity for PIR detection.
• If this occurs, reduce the PIR sensitivity setting from maximum to a medium point and re-check unit operation.
• If experiencing false triggering during fade down/Off, try increasing the fade time.
Lights do not turn ON:
Check for blinking red LED. If the LED blinks with long pulses, as opposed to short pulses, the sensor has reached its Hold Off setpoint
or Photocell Light Level setpoint.
Lights suddenly turn off and will not come back on:
Check for blinking red LED. If the LED blinks with long pulses, as opposed to short pulses, the sensor has reached its Hold Off setpoint
or Photocell Light Level setpoint.
There is no IR communication:
Perform a power cycle on the FSP-201.
During the sensor warm-up period, which can last up to 5 seconds after initial power-up (or after a lengthy power outage), the load will
remain ON until the selected time delay expires.
Catalog #
FSP-201
Digital High/Low PIR Fixture Integrated Sensor
FSIR-100
Configuration Tool
FSP-L2
360° lens, up to 44' diameter at 8' height
FSP-L2-S
360° lens, up to 44' diameter at 8' height, with shroud
FSP-L3
360° lens, up to 40' diameter at 20' height
FSP-L3-S
360° lens, up to 40' diameter at 20' height, with shroud
FSP-L7
360° lens, up to 100' diameter at 40' height
FSP-L7-S
360° lens, up to 100' diameter at 40' height, with shroud
FSP-C1
Small collar, for use with FSP-L2 and FSP-L3 lenses
FSP-C2
Large collar, for use with FSP-L7 lens
BZ-50
Power Pack: 120/277VAC, 50/60Hz, 20A ballast or incandescent
BZ-150
Power Pack: 120/277VAC, 50/60Hz, 20A ballast or incandescent, with Hold-On and Hold-Off capability
BZ-200
Power Pack: 120/277VAC, 50/60 Hz, 20A Ballast/ELV/MLV/Incandescent/LED, 16A, E-Ballast/CFL/Plug Load
BZ-250
Power Pack: 120/277VAC, 50/60 Hz, 20A, Ballast/ELV/MLV/Incandescent/LED, 16A E-Ballast/CFL/Plug Load,
with Hold-On/Hold-Off capability
BZ-250-347
Power Pack: 120/347VAC, 50/60 Hz, 16A Ballast/ELV/MLV/Incandescent/LED/ E-Ballast/CFL, 15A Plug Load,
with Hold-On/Hold-Off capability
Sensor is White.
OPERATION DURING POWER-UP
ORDERING INFORMATION
4
Description
Publicité
