LEGRAND Wattstopper FSP-201 Instructions D'installation

No: 23937 – 06/22 rev. 7
Catalog Number • Numéro de Catalogue • Número de Catálogo: FSP-201
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
DESCRIPTION AND OPERATION
The FSP-201 is a motion sensor that dims lighting from high to low
based on movement. This slim, low-profile sensor is designed for
installation inside the bottom of a light fixture body. The PIR lens
module connects to the FSP-201 through a 1.30" diameter hole in
the bottom of the fixture.
The sensors use passive infrared (PIR) sensing technology that
reacts to changes in infrared energy (moving body heat) within the
coverage area. Once the sensor stops detecting movement and
the time delay elapses, lights will go from high to low mode and
eventually to an OFF position if it is desired. Sensors must directly
"see" motion of a person or moving object to detect them, therefore
careful consideration must be given to sensor luminaire placement
and lens selection. Avoid placing the sensor where obstructions
may block the sensor's line of sight.
The FSP-201 operates at 12–32 VDC. It is designed to be installed
in indoor and outdoor environments.
PIR Sensor
Motion Indicator
Red LED
Sensor Protection Cap
NOTE: Remove Cap before use
Once powering the device up, the FSP-201 will use factory default
parameters to operate. If adjustments are needed, Wattstopper
FSIR-100 Wireless IR Configuration Tool must be used.
Wattstopper
Low Voltage High/Low/Off PIR Fixture Integrated Outdoor Sensor
Basse Tension, Haut/Bas/Éteint
Luminaire avec détecteur IRP extérieur intégré
Bajo Voltaje, Alto/Bajo/Apagado
Sensor PIR para luminarias y uso exterior
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
Voltage ........................................................................12–32 VDC
Current Consumption
Wiring Terminals
Operating Temperature ...................-40°F (-40°C) to 176°F (80°C)
Tightening Nut Torque .................................................25–30 in-lbs
Dimensions
Weight ........................................................................ 2.4 oz (70 g)
Coverage
Adjustments and Features
Light Sensor
IR Transmitter Factory Defaults
IR Receiver
OPEN DEVICE for installation in a Listed Enclosure per Installation
Instructions.
®
SPECIFICATIONS
Normal Operation .......................................................... 15mA
IR Programming ............................................................ 45mA
Primary Voltage ........................................... +VDC, Com, Ctrl
Control Output ........................................... 100 mA maximum
Dimming Voltage ...........Dim + (purple), Dim - (pink), Ground
Use Solid or Tinned Stranded Copper Conductor
.................................................................... 18AWG–20AWG
Collar ...............................................1.30" diameter (33.0mm)
Collar height ...................................................0.64" (16.3mm)
Body .........1.38" x 3.8" x 0.9" (35.1mm x 96.5mm x 22.9mm)
FSP-L2 Lens @ 8' height ...........................up to 44' diameter
FSP-L3 Lens @ 20' height .........................up to 40' diameter
FSP-L7 Lens @ 40' height .......................up to 100' diameter
High Mode ............................................................. 0 V – 10 V
Low Mode .............................................. . . . . 0 V – 9.8 V, Off
Time Delay ................................. 30 seconds, 1 min – 30 min
Cut Off ............................ Disable, 1 min – 59 min ,1 hr – 5 hr
Sensitivity ............................. On-Fix, Off-Fix, Low, Med, Max
Hold Off Setpoint ............................... Auto, Disable, 1–250 fc
Ramp Up ........................................... Disable, 1 sec – 60 sec
Fade Down ........................................ Disable, 1 sec – 60 sec
Photocell Setpoint for On/Off ..................... Disable, 1–250 fc
High Mode .......................................................................10 V
Low Mode .........................................................................1 V
Time Delay .................................................................... 5 min
Cut Off .............................................................................. 1 hr
Sensitivity ....................................................................... Max
Hold Off Setpoint ....................................................... Disable
Ramp Up .................................................................... Disable
Fade Down ................................................................. Disable
Photocell Setpoint for On/Off ..................................... Disable