NEC PlasmaSync 42XM4 PX-42XM4A Manuel D'utilisation page 34

Information
AUTO ID settings
ON: Enables Auto ID function. In the case shown below,
display 1 will be set as ID 1, display 2 as ID2, etc.
This can be set only when a 2×2 or 3×3 video wall is
selected.
No.1 No.2
REMOTE
No.4
IN
Display 1
No.1 No.2
REMOTE
OUT
No.4
OFF: Disables Auto ID function.
IMAGE ADJUST
The position of the image can be adjusted and flickering
of the image can be corrected.
Example: Adjusting the vertical position
On "VIDEO WALL" menu, select "IMAGE ADJUST", then
press the MENU/ENTER button.
The "IMAGE ADJUST" screen appears.
On "V-POSITION" of "IMAGE ADJUST" menu, adjust the
position.
IMAGE ADJUST
ASPECT MODE :
V-POSITION
H-POSITION
V-HEIGHT
H-WIDTH
AUTO PICTURE :
FINE PICTURE
PICTURE ADJ.
SEL. ADJ.
Information
IMAGE ADJUST settings
These are the same functions as the IMAGE ADJUST
menu on page En-22.
P. ON DELAY (Power on delay)
Use this function to activate power-on delay.
Turn on the AUTO ID before the following operations.
Example: Setting "ON"
On "P. ON DELAY" of "VIDEO WALL" menu, select
"ON".
DIVIDER
POSITION
DISP. MODE
AUTO ID
IMAGE ADJUST
P. ON DELAY
PLE LINK
REPEAT TIMER
SEL.
Information
P. ON DELAY settings
ON: Turns on the main power of each display after a
delay time.
OFF: Turns on the main power of all displays at the
same time.
(Only for 4×4 and 5×5 video wall modes)
MODE1: Turns on the main power of each display
delayed.
Downloaded From TV-Manual.com Manuals
REMOTE
OUT
No.1 No.2
No.3 No.4 No.3
REMOTE
IN
Display 2
REMOTE
OUT
No.1 No.2
No.3 No.4 No.3
REMOTE
IN
Display 3
Display 4
NORMAL
: ± 0
: ± 0
: 0
: 0
OFF
: 0
: 0
RETURN
EXIT
V-POSITION
VIDEO WALL
: 1
: SPLIT
: OFF
: ON
: OFF
: OFF
ADJ. EXIT RETURN
MODE2: Turns on the main power of each display more
delayed.
* Once this function has been set to "ON", the POWER
ON/OFF button on the remote control does not function
except for the No.1 monitor.
By pressing the POWER ON button on the remote
control the No.1 monitor will turn on and the others
will be turned on one by one automatically.
REMOTE
OUT
* From the second monitor onward, neither the POWER
button on the unit nor the POWER ON button on the
remote control works. However, by pressing and holding
the POWER ON button for more than 3 seconds, the
REMOTE
monitor will be turned on.
IN
PLE LINK
Use this function to set a uniform brightness for each
display.
Turn on the AUTO ID and set the DIVIDER (at 1, 4 or 9)
before the following operations.
Example: Setting "ON"
On "PLE LINK" of "VIDEO WALL" menu, select "ON",
then press the MENU/ENTER button.
Information
PLE LINK settings
: + 64
ON: Sets a uniform brightness for each screen in a video
wall. This can be set only when a 2×2 or 3×3 video
wall is selected.
OFF: Sets the individual screen brightness for each
screen in a video wall.
* When this function is set "ON", connect your plasma
displays with the remote cable (optional) in the order of
the position numbers for the 2×2 video wall. See the
drawing below.
* If there are changes in the DIVIDER or POSITION,
the PLE LINK will automatically turn OFF.
REMOTE
REMOTE
* With the 3×3 video wall, connect the final display to
the first display the same way as with 2×2 video wall.
Note: The remote control can be operated unless the
IR REMOTE is set to "OFF".
En-33
VIDEO WALL
DIVIDER : 1
POSITION
DISP. MODE : SPLIT
AUTO ID : OFF
IMAGE ADJUST
P. ON DELAY : OFF
PLE LINK : ON
REPEAT TIMER : OFF
SEL. ADJ. RETURN
EXIT
REMOTE
OUT
No.1 No.2
No.1 No.2
No.4
IN No.4 No.3
REMOTE
IN
Display 2
Display 1
REMOTE
OUT
No.1 No.2 No.1 No.2
OUT
No.4
No.4 No.3
REMOTE
IN
Display 3
Display 4
REMOTE
No.3 OUT
REMOTE
No.3
IN