Publicité
Déballage de votre scie
Moteur
Assemblage de
protège-lame
Guide à onglets
Assembling Your SawStop Contractor Saw
• Assemble the front of the stand by attaching two of the legs
Before assembling your saw, make sure that you
Assembling the Stand
marked
A
have all the components identified on pages 12 and
are in front of the front panel. Bumps on the legs fit into holes in
13 in the Owner's Manual, including hardware
the front panel to align the legs. Attach the legs to the front
pack #1 and hardware pack #2. Call the SawStop
• Locate the stand components labeled
through
and
panel using four M8 x 20 carriage bolts
A
F
hardware pack #1. All of the hardware needed to assemble the
four M8 lock washers
Service Department at 503-582-9934 if any
stand is located in the area with the blue background on
tighten the nuts at this time. Leaving the nuts loose will make it
components are missing. Hardware pack #2
hardware pack #1. In order to easily identify the hardware used
easier to align holes as you assemble the rest of the stand.
includes some of the tools needed to assemble
in each of the following steps, the different pieces of hardware
the saw. You will also need the following additional
are numbered on the hardware pack and on these assembly
tools:
instructions.
Hardware Pack
#
1
1. an 8 mm socket
Assembling the Stand
Hardware for Steps 1-9
Hex Nuts, M8
2. a 10 mm wrench
(32 + 2 extra)
4
3. two 13 mm wrenches
(24 + 2 extra)
Carriage Bolts, M8 x 20
1
4. a level or straight edge
Washers, M8
(32 + 2 extra)
2
Leveling Feet
(4)
5
Lock Washers, M8
(24 + 2 extra)
3
1
2
Mounting the Saw to the Stand
Hardware for Steps 10-14
Lock Washers,
6
M8 x 20 (4)
Hex Screws,
M8 (8)
Washers,
7
M8 (4)
8
Hex Nuts,
M8 (4)
9
• Assemble the rear of the stand by attaching the remaining two
• Attach one of the side panels marked
D
between the front and
• Repeat the prior step to attach the remaining side panel
legs marked
A
to the rear panel marked
C
. Make sure that the
rear portions of the stand. Make sure the legs are in front of the
marked
D
legs are in front of the rear panel. Bumps on the legs fit into holes
side panel and that the side panel is under the top flanges of the
in the rear panel to align the legs. Attach the legs to the rear
front and rear panels. Bumps on the legs fit into holes in the side
panel using four M8 x 20 carriage bolts
1
, four M8 washers
2
,
panel to align the legs. Use four M8 x 20 carriage bolts
1
,
four M8 lock washers
3
, and four M8 hex nuts
4
. Do not fully
four M8 washers
2
, four M8 lock washers
3
, and four M8 hex
tighten the nuts at this time.
nuts
4
to attach the side panel to the front and rear portions.
Do not fully tighten the nuts.
D
4
3
D
2
C
4
1
1
A
3
4
3
5
2
A
• Attach one of the short brackets marked
E
between the two
• Attach one long bracket marked
F
between the legs on the
• The front, rear and side panels have flanges that overlap to
front legs. Make sure the legs are in front of the bracket. Use
right side of the stand. Make sure the legs are in front of the
define mounting holes through which you will bolt the saw to
two M8 x 20 carriage bolts
1
, two M8 washers
2
, two M8 lock
brackets. Use two M8 x 20 carriage bolts
1
, two M8 washers
2
,
the stand. There is one hole in each corner of the stand.
washers
3
, and two M8 hex nuts
4
. Do not fully tighten the
two M8 lock washers
3
, and two M8 hex nuts
4
to attach the
Adjust the panels until the holes align and then tighten all of
nuts. Repeat this process to attach
long bracket. Do not fully tighten the nuts. Repeat this process
the nuts in the stand using a 13 mm wrench.
the remaining short bracket
E
to attach the remaining long bracket
F
between the legs on the
between the rear legs.
left side of the stand.
E
6
7
F
8
4
3
3
1
2
4
2
1
Mounting the Saw
• With the help of an assistant, pick up the saw and carefully set it
• Attach a foot
5
to the bottom of
on the assembled stand with the front of the saw above the front
each leg by threading an M8 hex
nut
on each foot and then
to the Stand
panel of the stand. Align the mounting holes in the bottom corners
4
placing an M8 washer
over
of the saw with the mounting holes in the top corners of the stand.
2
the nut. Insert a foot into the hole
While moving the saw do not set it down in the upright position on
at the base of each leg and then
a solid surface because the dust shroud can be damaged.
Warning! The saw weighs approximately 140 pounds. Be careful
place a second M8 washer
2
and
Hardware Pack
#
1
and use proper lifting technique to avoid injury.
thread a second M8 hex nut
4
Assembling the Stand
Hardware for Steps 1-9
(32 + 2 extra)
Hex Nuts, M8
4
onto each foot. Do not fully
4
Carriage Bolts, M8 x 20
tighten the nuts. The stand is
(24 + 2 extra)
1
now fully assembled.
2
Washers, M8
Leveling Feet
(32 + 2 extra)
2
(4)
5
Lock Washers, M8
(24 + 2 extra)
3
Mounting the Saw to the Stand
2
Hardware for Steps 10-14
Lock Washers,
8
6
Hex Screws,
M8 x 20 (4)
Washers,
M8 (8)
7
M8 (4)
M8 (4)
Hex Nuts,
9
Note: If you purchased an optional
4
mobile base for your saw, install it
now by following the instructions
that came with the mobile base.
9
10
• Remove the saw from the box and locate the
11
mounting hardware. All of the hardware needed to
5
mount the saw to the stand is located in the area with
the yellow background on hardware pack #1.
SawStop Service Department
503-582-9934
www.sawstop.com
© SawStop, LLC
Affiche d'installation
d'ensemble
Garde-courroie
Ensemble de manivelles
Couteau diviseur
Clés pour lame
to the front panel marked
. Make sure that the legs
B
1
, four M8 washers
2
,
3
, and four M8 hex nuts
4
. Do not fully
4
3
2
B
1
A
A
to the opposite side of the stand.
2
3
4
1
mounting holes
Flip to
Other Side
Ensemble matériel no.1
d'élévation
(deux)
Hardware Pack
1
#
Assembling the Stand
Hardware for Steps 1-9
Hex Nuts, M8
(32 + 2 extra)
4
Carriage Bolts, M8 x 20
1
(24 + 2 extra)
Washers, M8
Leveling Feet
2
5
(32 + 2 extra)
(4)
Lock Washers, M8
3
(24 + 2 extra)
Mounting the Saw to the Stand
Hardware for Steps 10-14
Lock Washers,
8
M8 (4)
Washers,
Hex Screws,
7
6
M8 (8)
M8 x 20 (4)
Hex Nuts,
9
M8 (4)
Courroie de moteur
Ensemble de manivelles
d'inclinaison
SawStop
®
10" CONTRACTOR SAW
OWNER'S MANUAL
Manuel d'utilisation
Hardware Pack
2
#
Installing the Motor and Belt Guard
Hardware for Steps 17-19
10
Washers, M5 (4)
Hex Nuts, M5 (4)
11
Mounting the Extension Wings
Hardware for Steps 20-21
Lock Washers,
Hex Screws,
12
13
M8 (8)
M8 x 16 (8)
Mounting the Switch Box
Hardware for Step 22
Washers,
Hex Screws,
Switch Box Keys
14
15
M6 (2)
M6 x 20 (2)
(2)
Tools
Blade Spacing
Adjustment
Gauge
(1)
Hex Key, M8
(1)
Hex Key, M5
(1)
Hex Key, M3
(1)
Ensemble matériel no.2
Banc de scie 10" SawStop
15
Publicité
