Silverline 254301 Mode D'emploi page 8

254301
Use as part of a fall arrest system
• Anchorages selected for fall arrest systems should be capable of
sustaining a static load, applied in the directions permitted by the
system of at least:
• 22kN for non-certified anchorages, or
• Two times the maximum arrest force for certified anchorages
• If more than one system is attached to one anchorage, the required
strength should be multiplied by the number of systems attached
Removing the harness
1. Ensure you are located in a safe place away from any fall hazards
2. Open both Leg Strap Buckles (6) by passing the three-bar slide through
the square link
3. Open the Chest Strap (2) buckle
4. Remove your arms from the harness
Note: Inspect the harness after use, and follow instructions for cleaning,
disinfection, transport and storage as outlined in 'Maintenance'.
Operation
Note: This equipment must ONLY be used by competent operators. All
users must be trained in its safe use. Inexperienced users must receive
instruction prior to using this equipment. A risk assessment must be
carried out before undertaking any operations requiring fall arrest
equipment.
WARNING: ALWAYS wear personal protective equipment appropriate
for the work area and type of activity, including but not limited to, eye
protection, gloves, hard hat, protective shoes and hearing protection.
Note: Check the correct fitting and adjustment at least every 2 hours
during use. This may save your life! Regularly check connections with
other equipment in the system, and ensure various system components
are correctly positioned with respect to each other.
Rescue plan
WARNING: A suitable and sufficient risk assessment must be carried
out before commencing with any kind of work at height, or any work
that requires the use of personal protective equipment (PPE) as a control
measure.
• The user must have a rescue plan and the means at hand to
implement it
• The plan must take into account the equipment and special training
necessary to effectively conduct prompt rescue under all foreseeable
conditions
Accessories
• Additional fall arrest gear, workwear and other personal protection
equipment is available from your Silverline stockist
Maintenance
Note: All fall arrest equipment must be regularly inspected, cleaned and
maintained by a competent person, in accordance with local laws and
regulations. Maintenance must be recorded in a dedicated service record
(see end of this manual).
WARNING: Carry out a visual and tactile inspection of all components
every time the equipment is used. Carry out a detailed examination if the
equipment has not been used for some time. Note: A thorough, detailed
examination of the equipment must be carried out at regular intervals, at
least once annually, or more frequently depending on use.
WARNING: It is ILLEGAL to carry out any kind of repair or modification to
this equipment.
WARNING: Should any damage be detected, remove the equipment from
service immediately. It must then be rendered unusable and discarded.
Visual/tactile inspection
The following defects potentially result in degradation and/or weakening
of equipment components:
• Cuts of 1mm or more at the edges of webbing
• Surface abrasion across the face of the webbing, at webbing loops and
around the edges
• Damage to stitching
• Knots other than those intended by the manufacturer
• Chemical attack potentially resulting in local weakening and softening
(often indicated by flaking of the surface). Discolouration of the fibres
may also be present
• Heat or friction damage indicated by fibres with a glazed appearance
which may feel harder than surrounding fibres
• UV-light degradation which can be difficult to identify, particularly
visually, but there may be some loss of colour (if dyed) and a powdery
surface
• Partially deployed energy absorber (e.g. short pull-out of tear webbing)
• Contamination (e.g. with dirt, grit, sand etc.) which may result in
internal or external abrasion
• Damaged, oxidised or deformed fittings (e.g. karabiners, screw link
connectors, scaffold hooks)
• Damage to the sheath and internal damage to the core of a rope
Note: See 'Service life and product obsolescence' if such damage or
other defects are detected during inspection.
Cleaning
Note: Correct cleaning is essential to ensure integrity of this equipment.
Follow the cleaning instructions below without deviation.
• Clean webbing straps and buckles in warm water (30 – 60°C) with
a mild pH neutral (pH7) household detergent. In the event of minor
soiling, wipe with a cotton cloth or carefully clean using a soft brush
• DO NOT under any circumstances use any abrasive materials, acids,
basic detergents or solvents
• Disinfect parts that come into contact with the operator's skin,
using a disinfectant suitable for the material of the equipment
(see 'Specification'). Strictly follow the disinfectant manufacturer's
recommendations and procedures
• ALWAYS allow the equipment to dry naturally, and keep it away from
open fire or any other heat source
Note: This also applies to equipment that has become wet during use.
Transport
• ALWAYS transport this equipment inside a dedicated bag or suitable
container that protects it from mechanical damage and shields the
equipment from high temperatures, humidity, UV rays and chemicals
Storage
• Store this tool carefully in a secure, dry place out of the reach of
children
• Store at moderate temperature and humidity, away from direct
sunlight or chemicals, inside a dedicated, UV-proof bag or container
• Never place heavy objects on top of this equipment
www.silverlinetools.com
Restraint Kit
9