Bimar Caldissimo S598.EU Notice D'instructions page 8

Fax +32 030 9904733

•
T
hat the user must not leave the appliance unattended while it is connected to the supply.
•
D
o not touch the heater with wet hands or feet.
•
D
o not expose the heater to the weather (sun, rain, etc.)
•
I
f the appliances falls or works badly, disconnect the electrical cable immediately. Check
that no part is damaged and switch it on after these controls: in case of doubt, contact
professionally qualified persons.
•
D
o not pull on the power cord or the appliance to unplug the appliance from the electric
socket.
•
I
f the electric cord is damaged, it has to be replaced by the supplier or an authorized service center
or a professionally qualified, to avoid any risks.
•
U
se this heating convector only and always in an upright position.
•
E
nsure that the appliance can heat up; for this purpose, check that the air inlet and outlet
openings are free from obstructions: do not leave anything hanging over or under the
appliance. In the event of overheating, the incorporated safety device stops the convector
heater from working.
INSTALLATION
• After removing the packing materials, check the integrity of the appliance; if you are unsure, do not
use it and ask for qualified professional help. The packing materials (plastic bags, polystyrene
foam, nails, etc.) must be kept out the reach of children because they are potential sources of
danger; but dispose of them in accordance with current law. Attention: please remove any
adhesive or advertising sheet stuck to the aspiration and air grid or to the base before use the
device.
• Before connecting the appliance, check that the voltage shown on the data plate matches that of
your electricity (220-240V~ 50Hz). In the event of incompatibility between the electric outlet and
the plug of the appliance, have the outlet replaced with another more suitable type by
professionally qualified personnel, who will make sure that the section of the wires of the outlet is
appropriate for the absorbed power of the appliance. In general, the use of adapters or extension
cords is not recommended; if their use is indispensable, they must conform to existing safety
standards and their current capacity (amperes) must not be less that the maximum of the appliance.
• Position the thermoconvector far from other sources of heat, inflammable materials (curtains,
carpets, etc.), inflammable gases or explosive materials (spray cans) and from materials that can
deform on exposure to heat. Make sure that there is 100 cm of free space in front of the appliance
and 30 cm on the sides. Do not use the heater in places where it could be subject to shocks in the
immediate vicinity of a bathtub, shower or swimming pool to avoid drops of water falling on the
heater or the heater falling in the water: If the appliance should accidentally get wet or be
submerged in water, remove the plug from the supply socket immediately and dry the unit
carefully. Check that no liquid has gone inside and if in doubt, contact professionally qualified
personnel.
• The support surface must be stable and not sloping (since the heater could tip over).
• Make sure that the cable is correctly positioned, that it is not touching hot elements or sharp edges,
is not wound around the utensil, is not twisted up on itself or in the way to prevent the utensil from
being pulled over. Check that you cannot trip over to prevent accidental falls or harm to persons.
• The appliance must not be positioned immediately under a socket.
• Please pay attention to the aspiration and dissipation air grids, in order to avoid obstructions, fire
risks or eventual device overheating. Please do not cover the device and do not use it to dry the
linen.
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
8 28
/
Assembly page 8/28