Bosch BGS41 Serie Mode D'emploi page 47

Vacuuming with accessories
12*
Figure
Attach the nozzles to the suction pipe or handle as re-
quired:
a) Hard-floor nozzle*
- with clip-in edge-cleaning bristles:
of hard floor coverings (tiles, parquet, etc.)
- without edge-cleaning bristles:
For cleaning dirt in gaps and cracks
‡
The edge-cleaning bristles can be removed by push-
ing the two catches in the direction of the arrows.
b) Crevice nozzle* for vacuuming crevices and corners,
etc.
c) Upholstery nozzle* for vacuuming upholstered furni-
ture, curtains, etc.
After each use, reinsert the combination nozzle into
the accessories holder.
d) Furniture brush
For cleaning window frames, cabinets, mouldings,
etc.
e) Mattress nozzle
For cleaning mattresses, upholstery, etc.
Drill dust nozzle
13*
Figure
‡
Fasten the drill dust nozzle onto the handle and posi-
tion it on the wall so that the drill hole opening on
the nozzle is placed directly over where the hole is
to be drilled.
‡
Set the appliance to the lowest power level and then
switch it on.
‡
The drill dust nozzle is held in the required position
by suction. Depending on the condition of the wall to
be drilled, you may need to adjust to a higher power
setting to ensure that the drill dust nozzle remains
in place.
During drilling, the fine dust is automatically vacu-
umed up.
Vacuuming with the Multi-Use-Brush
14*
Figure
Note: Do not remove the Multi-Use-Brush after use.
The suction power is not restricted by the fitted Multi-
Use-Brush.
!
ATTENTION!
Vacuuming without the bristle ring pushed down can
damage the surface.
Never vacuum with the bristle ring pushed up.
a) Push the Multi-Use-Brush onto the handle or the
tube and lock it in place.
b) Press the two locking catches on the bristle ring.
‡
Push the bristle ring down and lock it in place.
= The Multi-Use-Brush is ready to use. >
c) Vacuum using the Multi-Use-Brush.
‡
Press the two locking catches on the bristle ring.
‡
Push the bristle ring upwards and lock it in place.
d) Press the release button and remove the Multi-Use-
Brush to remove.
15
Figure
You can use the parking aid on the side of the appliance
if you want to stop vacuuming for a short time.
‡
After switching off the appliance, slide the hook on
the floor nozzle into the parking aid.
16
Figure
When vacuuming stairs, the appliance must be posi-
tioned at the bottom of the stairs. If it does not reach
far enough, the appliance can also be carried using the
carrying handle.After vacuuming
17
Figure
a) Switch off the appliance.
‡
Unplug the mains plug.
b) Briefly pull on the mains cable and then let go. (The
mains cable retracts automatically.)
18*
Figure
‡
Release the telescopic tube by moving the sliding
switch or adjusting sleeve in the direction of the ar-
row, and slide one tube into the other.
19
Figure
To store/transport the appliance, you can use the stor-
age aid on the underside of the appliance.
a) Prop up the appliance on the hose or dust container
handle.
b) Slide the hook on the floor nozzle into the storage
aid.
‡
In order to save space and to facilitate transport,
wind the suction hose around the appliance and the
telescopic tube.
c) The appliance can also be transported using the han-
dle on the dust container.
Disassembly
20
Figure
‡
To remove the suction hose, press the two catches
together and pull out the hose from the appliance's
air intake opening.
21*
Figure
a) Telescopic tube without accessory connection:
To release the connection, turn the handle slightly
and pull it out of the telescopic tool.
b) Telescopic tube with accessory connection:
To release the connection, press the locking collar
on the telescopic tube and and pull out the handle.
22*
Figure
a) Nozzle without accessory connection:
To release the connection, turn the telescopic tube
slightly and pull it out of the floor nozzle.
b) Nozzle with accessory connection:
To release the connection, press the locking collar
and pull the telescopic tube out of the floor nozzle.
* Dependent on model
47