Publicité
R
USE AND MAINTENANCE INSTRUCTIONS - WORKSHOP PRESSES
EXTREMELY IMPORTANT: Read these safety instructions carefully in addition to the instructions for assembly,
use, operation and maintenance. Keep them in a safe place for later consultation.
This press has been designed for general bending, toughening, axis and bearing extraction work etc. Never use it
for applications that should not be performed by a press. Always use the appropriate tool for each specific task.
Handle the press correctly and ensure that all parts and components are in good condition and that no parts are
missing prior to its use.
The press should only be used by authorized persons, having read carefully and understood the contents of this
manual and the assembly instructions.
Do not modify the press in any way.
Non-compliance with these instructions may result in injury or damage to the user, the press or the piece being
manipulated.
The manufacturer accepts no responsibility for the improper use of the press or the component handled.
Noise level less than 70 dB(A) for pneumatic presses.
1. SAFETY INSTRUCTIONS
1.1. Never exceed the rated capacity of the press.
1.2. Keep unauthorised persons away from the work area.
1.3. Always position the press against a wall. If the press is situated in the open workshop, it is essential that
a guard be placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece
ejecting suddenly.
1.4. The work tables, and presses in general, are heavy elements which must be handled with care. In presses
which are not equipped with a winch, the user must request the help of other people to position the table in its
work position and / or whenever the working height needs to be altered.
1.5. Do not introduce hands or any other part of the body in the work area.
1.6. Exposed personnel in the work zone are obligated to protect their feet, face and hands. Steel or other
materials may splinter or fall due to the strong pressure put on them by the press.
1.7. Never wear baggy clothes, ties, watches, rings, chains, etc. when using the press. Long hair should be tied
up.
1.8. As a safety measure, the models have an overload valve, set at its maximum working pressure at the factory.
This valve should not be tampered with under any circumstances.
1.9. IMPORTANT: Before using accessories, punches and V-block, check their maximum capacity on pages 8 and
9.
2. ASSEMBLY, USE AND OPERATION
2.1. The press is delivered palletized or packaged. If using either a transpallet or a crane to move the structure,
ensure that the press is balanced to prevent tipping.
2.2. Unpackage and place the legs as shown at the beginning of the manual, to place the press on a firm, regular
and horizontal surface.
2.3. Ensure that the work area is sufficiently lit.
2.4. We recommend leaving at least enough space around the press so that the different storage and maintenance
compartments may be completely opened to accommodate material pieces of greatest size.
2.5. The press is stable enough to work without being anchored, but if located in an area of movement (cranes,
wheelbarrows, etc.) it is advisable to anchor it.
2.6. Only for models with pneumatic pump: Couple the hose to the ¼ male gas connection, located on the back
of the press. An acceptable supply pressure oscillates between
2.7. Always place the 2 axles (4 axles for the 50t model
with fixed cylinder) in a position appropriate for the
operation to be performed.
VERY IMPORTANT: Ensure that the table is firmly
resting on the axles. Especially for presses with a winch.
2.8. GENERAL OPERATIONAL DESCRIPTION:
•
Place the wedge on the press table, then attach the work piece on the wedge.
•
Close the release valve by turning it to the right until it is firmly closed.
•
Activate the pump until the piston approaches the piece.
•
Align the piece and the piston so that the piece is properly centered.
•
Activate the pump to apply pressure to the piece.
•
When the work is finished, stop the pump and open the release valve by turning it to the left so as to remove
the piece.
•
Once the press has been used, keep the piston, screw and the pump piston fully retracted.
10050001001.12.
May
.20
7-10 bar (100-145 psi)
2 ejes/axle/arbre/achsen
EN
.
4 ejes/axle/arbre/achsen
18
Publicité
