Table des Matières
Publicité
Liens rapides
Signal Booster
Installation
Guide
Direct Connect
Signal Boosters
Contents:
How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
In-Vehicle Wilson Installation
Outside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Signal Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Lightning Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . 6
In-Building Wilson Installation
Outside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Signal Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Powering Up a Wilson Signal Booster . . . . . . . . . . . . . . . . 8
Warnings and Recommendations . . . . . . . . . . . . . . . . . . . 9
Guarantee and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10
Signal Booster Specifications . . . . . . . . . . . . . .Back Cover
Note: This manual contains important safety and operating information .
Please read and follow the instructions in this manual . Failure to do
so could be hazardous and result in damage to your Signal Booster .
Wilson
®
Electronics, Inc.
Publicité
Table des Matières
Sommaire des Matières pour Wilson Signal Boosters
-
Page 1: Table Des Matières
Signal Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Powering Up a Wilson Signal Booster . . . . . . . . . . . . . . . . 8 Warnings and Recommendations . -
Page 2: How It Works
(301101) How it Works Wilson Electronics Signal Boosters are small, portable, bi-directional devices that deliver service levels consistent with what would be expected in areas of high cell network coverage . They amplify a weak or shadowed signal in mobile, marine, M2M and in-building applications . -
Page 3: Before Getting Started
Before Getting Started This guide will help you properly install Wilson’s Direct Connect Signal Boosters in both in-vehicle and in-building applications . It is important to read through all of the installation steps for your particular application prior to installing any equipment. - Page 4 The antenna cable is small enough to easily tuck under the door seal or plastic molding . Tuck Cable Under Seal NOTE: See RF Safety Warnings (p. 9) Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST.
-
Page 5: Outside Antenna
Supply until the Outside Antenna and external adapter cables are attached to the Signal Booster . Cell Phone DC Power Supply Adapter Signal Booster Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST. -
Page 6: Adapter
“Inside Antenna” on the Signal Booster . NOTE: Depending on your specific cell phone, the adapter socket may be located beneath a rubber plug. Figure 1 Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST. -
Page 7: Lightning Surge Protection
In-Vehicle/In-Building Extension Cable Chart The following Wilson extension cables are available to help you customize your installation for peak performance . 5’ Extension Cable RG58U 75’ Extension Wilson 400 951101 Low Loss Coax 952375 (9913 Equivalent) Ultra Low Loss Coax 10’... - Page 8 (sold separately) to the power input labeled “12V DC” on the Signal Booster . Recommended installation locations for in-building are: • On a wall • On the ceiling • Near a power outlet Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST.
-
Page 9: Powering Up A Wilson Signal Booster
. You should see a signal improvement of 2 or more bars . Note: Many phones take up to 20 seconds to reset the bar indicator. Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com... -
Page 10: Warnings And Recommendations
Signal Booster . Lightning protection is recommended for all in-building installations . NOTE: The aluminum casing of a Wilson Signal Booster will adjust very quickly to the ambient temperature of its environment. For example, in the summer, when the inside of a car can reach 140 degrees Fahrenheit, the Signal Booster temperature may be 150 degrees or higher. - Page 11 Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase . Signal boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics .
-
Page 12: Signal Booster Specifications
Signal Booster Specifications Dual-Band 800/1900 MHz Specifications Model Number / Part Number 2B1401 / 811207, 811209 Connectors FME-Male Impedance (input/output) 50 ohms Dimensions 5 x 5 .4 x 1 .4 inch or 14 x 10 .8 x 3 .5 cm Weight 1 .32 lbs or 0 .6 kg Frequency...