Niko 310-0190 Serie Mode D'emploi page 8

310-0190X
Attention: The dimmer is never electrically separated from the mains voltage. All parts remain connected to the
mains voltage even if the load (e.g. the light) is off.
4.3. Memory function
Use
The standard setting of the dimmer is without memory function. You can use the fourth DIP switch behind the
control button to activate or deactivate this function:
DIP switch position
DIP switch up
DIP switch down
The last dimming level set before switching off the dimmer is saved in the permanent memory of the dimmer if
the memory function is activated. In the event of a power failure, this value will not be lost.
If the memory function is activated, the dimmer switches on for the first time at the default dimming level chosen
by the manufacturer. Thereafter, the lighting will be dimmed at the last set value.
Dimming dimmable economy lamps with memory function
The dimming profile is set up so that the dimmer is first switched on to its maximum light intensity for a short
time and then returns to the dimming level saved in memory. All economy lamps can be switched on like this.
5. TROUBLESHOOTING
The operation of the dimmer can be disturbed by signals that are sent over the mains. This is not a defect.
Problem Cause
The dimmer is not working. The mains voltage is discon-
The red LED on the dimmer nected.
is not on.
The wire is defect.
The dimmer is not working. The load is disconnected.
The red LED on the dimmer
is on.
The lamp or wire is defect.
The minimal dimming level is
set too low.
The dimming profile is wrong.
The dimmer switches off by The protection against thermal
itself. The red LED on the overload (temperature is too
dimmer is flashing. high) and short circuits has
been activated.
The dimming profile is wrong.
The lamp is flashing. The lamp is not dimmable.
The minimal dimming level is
set too low.
The dimming profile is wrong.
There is a PLC malfunction.
The lamp is not suitable.
The dimmer is defect.
The lamp cannot be switched There is current leakage.
off.
EN
nv Niko sa
Result
memory function on
memory function off
Action
Connect the device to the mains
voltage.
Replace the wire.
Connect the load correctly using the
wiring diagram.
Replace the lamp or wire.
Increase the minimum dimming level
or use a profile with boost function
(LED 3 or LED 4).
Choose another profile and adjust the
minimum dimming level.
Check if the lamp is dimmable. This
is shown on the packaging by the
following symbol:
Check whether the load is too high.
When doing this, keep in mind the
reactive power of ferromagnetic
transformers.
Check the temperature in the flush-
mounting box (max. 35 °C).
Check whether mixed loads are
being used.
For LED lamps, use the profiles in the
following order of preference:
- LED 1
- Incandescent lamp
- LED 3 (with boost function)
Check if the lamp is dimmable. This
is shown on the packaging by the
following symbol:
Increase the minimum dimming level
or use a profile with boost function
(LED 3 or LED 4).
Choose another profile and adjust the
minimum dimming level.
Place a PLC filter (Ripple Control
Rejector)
Replace the lamp if it flashes during
dimming the light up and down.
Replace the dimmer
Place a bypass
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
6. TECHNICAL DATA
power supply voltage
mounting
weight
no-load power consumption
max. housing temperature (Tc) at 35°C (Ta)
max. ambient temperature (Ta)
capacity 1
max. wire diameter per connection terminal
min. load
protection
max. distance between dimmer and rotary button
extension(s)
standards
The capacity to be dimmed drops 10% for every 5°C that the ambient temperature rises above 35°C.
1
100%
95%
90%
85%
80%
75%
70%
65%
60%
55%
50%
0 10 20
Ambient temperature (°C)
7. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the statutory regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file,
and it should be passed on to any new owners. Additional copies are available on the Niko website or via
the Niko support service.
• During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EC declaration of conformity regarding this product at www.niko.eu.
8. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
9. GUARANTEE PROVISIONS
• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of
purchase of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months after
stating the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point. Together with producers
and importers, you have an important role to play in the advancement of sorting, recycling and reusing discarded electrical
and electronic appliances. In order to finance the waste collection and processing, the government levies a recycling
contribution in some cases (included in the purchase price of this product).
230 Vac ± 10%, 50 Hz
flush-mounting box with flush-mounting depth of
min. 40 mm
± 70 g
< 0,5 W
90°C
see capacity graph below
dependent on the ambient temperature
(see capacity graph below)
2 x 2,5 mm²
5 W
protected against thermal overload and short-
circuit
75 m
EN60669-2-1
30 40 50
PM310-0190XR16015
60