Publicité
Les langues disponibles
Les langues disponibles
Operating Instructions
FPPS 24-18W-N POWER PACK
Item No. 2265888
24 V / 750 mA
Intended Use
The power pack serves as voltage supply for low-voltage devices with matching DC jacks. It is intended
for connection to common household mains voltage (100 - 240 V/AC, 50/60 Hz). A galvanic separated
DC voltage is applied to the output. The power consumption of the consuming device may not exceed the
nominal voltage of the respective power pack (depends on the type). The product has a protection against
short circuit and overload.
This product fulfils European and national requirements related to electromagnetic compatibility (EMC).
CE conformity has been verified and the relevant statements and documents have been deposited at the
manufacturer.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use
can result in short circuits, fires, electric shocks or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and prod-
uct names are trademarks of their respective owners. All rights reserved.
Delivery Content
•
Power pack
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health, e.g. due to an
electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important information in
these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
This symbol indicates that the product meets the energy efficiency requirements for Class VI.
Safety Instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General Information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can dam-
age the product.
• Never touch the device with wet or moist hands. There is a danger of electrocution.
• On commercial premises, the accident prevention regulations of the relevant professional
insurance association for electrical systems and operating materials are to be observed.
• Operation in unfavourable ambient conditions is not permitted. Adverse ambient conditions
are:
- moisture or excessive humidity
- dust and combustible gases, vapours or solvents
• Since the device generates heat when operating, ensure that it is adequately ventilated. The
housing must not be covered!
• Never switch the device on immediately after having taken it from a cold to a warm environ-
ment. Under adverse conditions, the resulting condensation could destroy the device. Allow
the device to reach room temperature before switching it on.
• Power units are not designed for application to human beings or animals.
• Consult an expert when in doubt about the operation, safety or connection of the appliance.
•
Operating instructions
• Maintenance, modifications and repairs must only be completed by a technician or an au-
thorised repair centre.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
b) Connected Devices
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
Operation
Periodically check the technical safety of the device, e.g. check for damage to the housing etc.
Always lay the cable so that nobody can trip over or become entangled in it. This poses a risk of
injury.
•
Connect the DC plug of the power pack with the DC jack on the low-voltage device.
•
The polarity cannot be altered. The plug has the fixed polarity "inside plus (+), outside minus (-)".
•
Make sure that the consumer is switched off when connected to the power pack.
•
Plug the power pack into a standard domestic wall socket. Correct operation is signaled at the power
pack by a LED.
•
To remove the consumer, proceed in reverse sequence.
Troubleshooting
By purchasing the power pack you have acquired a product that has been designed to the state of the art
and is operationally reliable. Problems and malfunctions can occur nevertheless. We would therefore like to
show how you can rectify certain faults yourself:
Observe the safety instructions by all means!
Problem
Cause
No mains voltage.
The power indicator
is not lit.
Power pack overloaded.
Care and Cleaning
•
Disconnect the product from the mains before each cleaning.
•
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can
cause damage to the housing and malfunctioning.
•
Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Input voltage ..........................................................100 – 240 V/AC
Input AC frequency ................................................60/50 Hz
Output voltage .......................................................24.0 V/DC
Output current ........................................................0.75 A
Output power .........................................................18.0 W
Average active efficiency .......................................86.9 %
Efficiency at low load (10%) ..................................75.9 %
No load power consumption ..................................0.1 W
Model identifier:
Commercial registration number:
Manufacturer:
Cable length ..........................................................1.8 m
Plug Ø: ...................................................................5.5 mm (outer) / 2.1 mm (inner)
Operating conditions ..............................................0 to +40 ºC, 20 – 85 % RH
Storage conditions .................................................-20 to +60 ºC, 10 – 90 % RH
Dimensions (W x H x D) ........................................51 x 73 x 82 mm
Weight ...................................................................130 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
Solution
Check the circuit breaker of the power outlet.
Check the correct fit of the power outlet.
Remove the consumer and check the technical data.
FPPS 24-18W-N
HRB 3896
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
*2265888_v2_0820_02_mxs_m_en
Publicité
