Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
6 Additional Functions
GB
6.1 Maximum brightness of the spotlight
If the maximum brightness of the spotlight is not
required, the brightness may be reduced to 33 % of
its maximum value. Thus, the brightness can be set
more precisely, because the 255 brightness levels
are available for a smaller brightness range.
1) Press the button MENU repeatedly until the
highest menu level has been reached.
2) Press the button UP or DOWN repeatedly until
the display indicates
3) Press the button ENTER. The display indicates
,
,
4) Press the button UP or DOWN repeatedly until
the display indicates
5) Press the button ENTER. The display indicates
the current setting:
= maximum brightness
= brightness reduced to 33 %
6) To be able to control the spotlight by DMX, use
the button MENU to return to the highest menu
level.
For an independent operation, use the button
MENU to select the operating mode and then
press ENTER to activate the mode selected.
6.2 White balance
The factory setting of the spotlight is such that the
colours red, green and blue – when set to maximum
brightness – result in a specific shade of white. This
shade of white may be changed to appear warmer
or colder, e. g. to level out the differences to other
spotlights when they are controlled together with
the PARC-56 / RGB or PARC-56 / RGB.
1) Press the button MENU repeatedly until the
highest menu level has been reached.
2) Press the button UP or DOWN repeatedly until
the display indicates
3) Press the button ENTER. The display indicates
.
4) Press the button ENTER again. The display
now indicates ,
000 and 255.
= brightness of colour red
= brightness of colour green
= brightness of colour blue
5) Use the button ENTER to select the three set-
ting options one after the other; use the button
UP or DOWN to set the brightness for the indi-
vidual colours and thus to create the shade of
white desired.
18
.
,
,
or
.
.
or
and a number between
6) To activate the shade of white that has been set:
a) Press the button MENU repeatedly until the
display indicates
b) Press the button DOWN twice so that the
display indicates
c) Press the button ENTER. The display
changes to
d) Press the button UP or DOWN repeatedly
until the display indicates
e) Press the button ENTER. If the display indi-
cates
indicates
to set the indication to
.
7) To be able to control the spotlight by DMX, press
the button MENU twice to return to the highest
menu level.
For an independent operation, use the button
MENU to select the operating mode and then
press ENTER to activate the mode selected.
6.3 Slow response of the LEDs
LEDs immediately respond to a change of the
brightness setting. To simulate the slow response
of standard lamps, the response can be set in four
steps. For the 10-channel operation
ting is made via DMX channel 9 (
4- and 5-channel operation, make the setting as fol-
lows:
1) Press the button MENU repeatedly until the
highest menu level has been reached.
2) Press the button UP or DOWN repeatedly until
the display indicates
3) Press the button ENTER. The display changes
to
4) Press the button UP or DOWN repeatedly until
the display indicates
5) Press the button ENTER. The display indicates
the current setting:
Use the button UP or DOWN to select the set-
ting desired.
6) To be able to control the spotlight by DMX, use
the button MENU to return to the highest menu
level.
For an independent operation, use the button
MENU to select the operating mode and then
press ENTER to activate the mode selected.
again.
.
,
,
.
, the shade of white is activated; if it
, use the button UP or DOWN
.
,
,
,
,
.
= immediate response
= slightly slow response
= slow response 2
= slow response 3
= slowest response
,
,
or
.
.
, the set-
fig. 8). For 3-,
or
.
Publicité
Table des Matières
