Installing The Product; Manual Running; Rack Assembling; Limit Switch Fixing - Key Automation TURBO 250 Instructions Et Avertissements Pour L'installation Et L'usage

4 - INSTALLING THE PRODUCT

4.1 - Installing
ATTENTION !
The installer must verify that the working temperature range
stated on the automation device is suitable for the location
where it is installed.
ATTENTION !
The automation system must be equipped with a pressure-sen-
sitive edge protecting all possible crushing points (hands, feet,
etc.) in accordance with the requirements of the EN 13241-1
standard.
ATTENTION !
The gate has to be equipped with stop locks at the opening and
closing, which prevent the gate derailment.
Before starting installation, you should carry out the following
checks, as well as making sure the structure is compliant with
current standards.

4.2 - Manual running

Insert the key in position 1 lock and rotate 90° counter-clockwise (fig.3).
4.3 - Fixing
Open the packaging and check the condition of all the parts of the
automation.
Remove the lid unscrewing the screws see (fig.5.1).
Place the gearmotor on the foundation plate matching the slots with
the protruding screws (B1).
Insert the 4 washers + locknuts to fix the gear (fig.5.2).
If the allowed adjustment of the ratchet is not sufficient it is possible
to compensate the height of the reduction gear working on the 4

4.4 - Rack assembling

Depending on the type of pinion used, the rack must be mounted at
a height, relative to the foundation plate, indicated by the dimension
B (Fig. 6).
For the correct installation of the ratchet unlock the reduction gear
as shown in (fig.3) and bring the gate to complete aperture.
Lay one element of the ratchet on the pinion and fix the latter with
screws and tingles to the gate.
Manually move the gate bringing the pinion in correspondance with
the last tingle.

4.5 - Limit switch fixing

The gate must feature check stops for aperture and closure that
prevent the gate from derailing.
The position of the limit device must ensure that the limit devices
do not collide with the pinion.
Manually open the gate leaving, based on the weight of the gate, a

4.6 - Limit switch setting

ATTENTION !
The opening and closing limit switches must intervene at least
X cm before the mechanical end stop (fig. 8)
Depending on the model, set on the control panel CT 102i, the pro-
Also check that the gearmotor's installation zone is compatible
with its overall dimensions (Fig.1).Create a solid concrete footing
and fix the base plate to the ground immerging it into the concrete
using the bracket clamps and fixing screws (Fig.4). If the base
already exists use robust expanding wedges;
ATTENTION !
The exact dimensions of the rack must be known to allow
precise calculation of the counterplate position (Fig. 6).
Provide one or more pipelines for the laying of electrical cables.
Fig.2 shows a typical installation:
Post for photocells (1)
Automation electromechanical (2)
Photocell detectors (3)
Flashing light (4)
Key switch (5)
Radio transmitter (6)
Pressure-sensitive edge (7)
Insert the unlock key in position 2 and rotate clockwise until complete
unlock of the pinion (fig.3).
more external screws B2 (fig.5.2).
Once the adjustment is finished firmly fix the 4 locknuts, making
sure that during the entire run of the gate, the reduction gear is
firmly to the ground.
The screws should be tightened again after the motor has been
operated a few times.
Definitively fix the element of the ratchet.
For the correct positioning of the other elements and to ensure
they are straight it is necessary to use a ratchet element using it as
reference and support (Fig. 6.2).
Moreover it is necessary to ensure some air between the ratchet
and the pinion of about 2 mm (indicative measure), so that the
weight of the gate does not bear upon the pinion of the reduction
gear (Fig. 6.1).
space between 30 a 50 mm. between the gate and the mechanical
stop.
Fix the limit device using the pins (fig.7.2) leaving a space between
the magnetic limit device and the reduction gear of max 10 mm
max (fig.7.1) repeat the operation with the gate closed.
gramming values LSI and EL.F. as indicated in the table
MODEL
LSI
SC202MHD
SC252M *
* without electro-brake
EL.F.
0 0 5 cm
0 15 10 cm
EN
X
11