Whirlpool CAM2752 Instructions D'installation page 3

word "DANGER" or "WARNING".
These words mean:
Before you start...
Your safety and the safety of others are very important.
Check location where washer will be
We have provided many important
installed. Proper installation is your
safety message in this manual and
responsibility. Make sure you have
on your appliance. Always read
everything necessary for correct
and obey all safety messages.
installation.
Do Not store or operate washer below
32°F (0°C) (some water may remain in
washer).
hurt you and others.
All safety messages will be preceded
by the safety alert symbol and the
word "DANGER" or "WARNING".
These words mean:
Check location where washer will be
installed. Proper installation is your
responsibility. Make sure you have
everything necessary for correct
installation.
Do Not store or operate washer below
32°F (0°C) (some water may remain in
washer).
Untape and
open washer
lid. Remove
packages and
hoses from
washer.
®
No. T20 TORX
†
screws
Front access to the pump area is
available by removing 2 No. T20
Torx screws and then removing the
®
†
Untape and
front panel.
open washer
lid. Remove
IMPORTANT: Observe all governing
packages and
codes and ordinances.
hoses from
washer.
PAGE 2
No. T20 TORX
screws
Front access to the pump area is
available by removing 2 No. T20
Torx screws and then removing the
®
†
front panel.
IMPORTANT: Observe all governing
codes and ordinances.
PAGE 2
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
Single washer
installations require
12-inch (300 mm)
minimum risers to
provide an air
cushion and
This is the safety alert symbol.
avoid noise and
This symbol alerts you to
damage to valves.
potential hazards that can kill or
®
†
DANGER
Grounded
electrical outlet
You can be killed or seriously
is required. See
injured if you don't immediately
Electrical
follow instructions.
requirements.
WARNING
You can be killed or seriously
injured if you don't follow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
Single washer
installations require
12-inch (300 mm)
minimum risers to
provide an air
cushion and
avoid noise and
damage to valves.
Level oor: Maximum slope
under washer — 1 inch (25 mm).
A oor drain should be
provided under the bulkhead.
Prefabricated bulkheads with
electrical outlets, water supply
lines, and drain facilities should
be used only where local
codes permit.
® TORX is a registered trademark of Saturn Fasteners, Inc.
†
Level oor: Maximum slope
under washer — 1 inch (25 mm).
A oor drain should be
provided under the bulkhead.
Prefabricated bulkheads with
electrical outlets, water supply
lines, and drain facilities should
be used only where local
codes permit.
Hot and cold water faucets: Must be
within 4 feet (1.2 meters) of the back
of the washer and provide water
pressure 10 - 100 PSI (69-690 kPa). A
pressure reduction valve should be
used in the supply line where inlet
pressure entering the building
exceeds 100 PSI (690 kPa) to avoid
damage to the washer mixing valve.
Hot and cold water faucets: Mus
within 4 feet (1.2 meters) of the back
of the washer and provide water
Grounded
pressure 10 - 100 PSI (69-690 kPa). A
electrical outlet
pressure reduction valve should be
is required. See
used in the supply line where inlet
Electrical
pressure entering the building
requirements.
exceeds 100 PSI (690 kPa) to avoid
damage to the washer mixing valve.
Water heater: Set to
deliver 120°F (49°C)
water to the washer.
Standpipe drain system: Needs a two-
inch (50 mm) minimum carry-away
capacity of 17 gallons (64.4 liters) per
minute. Top of standpipe must be at
least 39 inches (990 mm) high and no
higher than 72 inches (1.83 m) from
bottom of washer.
IMPORTANT: Floor must be sturdy
enough to support loaded washer
weight of 315 pounds (143 Kg).
Standpipe drain system: Needs a
inch (50 mm) minimum carry-away
capacity of 17 gallons (64.4 liters) per
minute. Top of standpipe must be at
least 39 inches (990 mm) high and no
higher than 72 inches (1.83 m) from
bottom of washer.
IMPORTANT: Floor must be stur
enough to support loaded washer
weight of 315 pounds (143 Kg).
® TORX is a registered trademark of Saturn Fasteners, Inc.
†
Water heater:
deliver 120°F (49
water to the wa
3