NEFF T47PD7BX2 Notice D'installation page 22

Flush installation
With the flush installation, the appliance and worktop
are on one level. There is no unattractive stepping
between the appliance and the worktop.
You can install the appliance in the following
temperature-resistant and waterproof worktops:
¡ Stone worktops
¡ Plastic worktops, e.g. Corian®
¡ Solid wood worktops
Installation in compressed-wood worktops is not pos-
sible.
Preparing the units
Requirement: The fitted units must be heat-resistant
up to 90 °C.
Mark the unit cut-out in accordance with the in-
1.
stallation diagram.
→ Fig.
14
Drill four holes with a diameter of 6 mm.
2.
→ Fig.
24
Ensure that the angle of the cut surface to the
3.
worktop is 90°.
→ Fig.
24
Observing the minimum clearances when in-
stalling above a drawer
When removing the overflow container on integ-
1.
rated appliances, take the minimum clearances
into consideration.
→ Fig.
11
Observe the position of the overflow container.
2.
→ Fig.
12
Preparing the unit for circulating-air mode with the
adapter
Observe the relevant dimensions when combining
1.
with the adapter for the cut-out in the back wall.
→ Fig.
25
Use the template to create the cut-out in the back
2.
wall.
In circulating-air mode, establish an air outlet in
3.
the unit's plinth.
Provide a minimum air outlet cross-section of
‒
approx. 440 cm².
To keep the draught and noise low, ensure that
‒
the outlet opening in the base panel is as large
as possible.
To guarantee that the appliance works correctly,
4.
ventilate the hob appropriately via an air outlet
with a minimum cross-section of 200 cm² in the
base unit.
After making the cut-outs, remove any shavings.
5.
Seal the cut surfaces so that they are heat-resist-
6.
ant and waterproof.
→ Fig.
24
Preparing the unit for circulating-air mode with a
circulating-air duct
If required, remove the unit's back wall.
1.
Observe the relevant dimensions when combining
2.
with the flat duct elbow for the cut-out in the back
wall.
→ Fig.
26
In circulating-air mode, establish an air outlet in
3.
the unit's plinth.
Provide a minimum air outlet cross-section of
‒
approx. 440 cm².
To keep the draught and noise low, ensure that
‒
the outlet opening in the base panel is as large
as possible.
22
To guarantee that the appliance works correctly,
4.
ventilate the hob appropriately via an air outlet
with a minimum cross-section of 200 cm² in the
base unit.
After making the cut-outs, remove any shavings.
5.
Seal the cut surfaces so that they are heat-resist-
6.
ant and waterproof.
→ Fig.
24
Preparing the unit for air extraction mode
If required, remove the unit's back wall.
1.
Observe the relevant dimensions when combining
2.
with a flat duct elbow for the cut-out in the back
wall.
→ Fig.
27
After making the cut-outs, remove any shavings.
3.
Seal the cut surfaces so that they are heat-resist-
4.
ant and waterproof.
→ Fig.
24
Attaching adhesive tape
Attach the enclosed adhesive tape to the worktop
▶
section.
→ Fig.
28
Installing the appliance
WARNING ‒ Risk of injury!
Parts that are accessible during installation may
have sharp edges and may lead to cutting injuries.
Wear protective gloves
▶
The appliance is heavy.
To move the appliance, two people are required.
▶
Use only suitable tools and equipment.
▶
Install the appliance for air extraction mode
▶
→ Page 23, circulating-air mode → Page 22 or
circulating-air mode with circulating-air duct
→ Page 23.
Note: The appliance is only intended for flush install-
ation.
Installing the appliance for circulating-air mode
with adapter
Note: When installing directly on a non-insulated
outer wall (µ ≥ 0.5 W/m² °C), we recommend a con-
figuration with circulating-air duct.
For the circulating-air mode, use the adapter and
1.
the odour filter.
Ensure that the clearance between the appliance
2.
and the rear panel of the unit is between 10 and
80 mm.
Attaching the adapter
Clean and degrease the adhesive surface around
1.
the cut-out in the unit's back panel.
Insert the adapter into the outlet opening on the
2.
rear of the hob.
→ Fig.
29
Remove the adhesive tape's protective film from
3.
the adapter.
→ Fig.
30
Inserting the appliance into the worktop cut-out
Ensure that the connection cable is connected to
1.
the appliance.
Carefully insert the appliance into the worktop cut-
2.
out.
→ Fig.
31
Securing the adapter
Hold the adapter at the central holder and use the
1.
side holders to slide it towards the unit's back
panel in the base unit, then affix it.
→ Fig.
32