Publicité
TECHNICAL DATA
SCREWDRIVER - CHARGER
Production code............................................................................
Tool reception ...............................................................................
Wood screws (without pre-drilling) ...............................................
No-load speed, 1st gear ...............................................................
No-load speed, 2nd gear ..............................................................
Torque
Low torque max.*1 ....................................................................
High torque max.*1 ....................................................................
Battery voltage..............................................................................
Weight with battery .......................................................................
Recommended ambient operating temperature ...........................
Recommended battery types........................................................
Recommended charger ................................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ............................................
The noise level when working can exceed 85 dB (A).
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 62841.
Screwing
Vibration emission value a
.......................................................
h
Uncertainty K .............................................................................
Drilling into metal:
Vibration emission value a
.......................................................
h
Uncertainty K .............................................................................
Voltage range ...............................................................................
Quick charge current ....................................................................
Battery charging time Li-Ion 2.0 Ah ..............................................
Weight without cable ....................................................................
*1 The values stated are reference values.
Actual values might differ, depending on the material and quality
of the screws.
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test
given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and
the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SCREWDRIVER SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a „live" wire may make
exposed metal parts of the power tool „live" and could give the
operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
18
ENGLISH
M4 D
M4 C
.......................4404 76 05...
...000001-999999
.......................... 1/4" (6,35 mm)
............................4,5 mm
...........................200 min
-1
...........................600 min
-1
............................3,5 Nm
...............................5 Nm
...............................4 V
...........................456 g
........................-18...+50 °C
........................... M4B2...
............................. M4 C
.............................58 dB (A)
........................ < 2,5 m/s
2
............................1,5 m/s
2
........................ < 2,5 m/s
2
............................1,5 m/s
2
................................. .................................... 4 V
................................. .................................... 3 A
................................. .................................. 45 min
................................. ................................ 354 g
Do not machine any materials that present a danger to health
(e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive
force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse
or by burning them. Milwaukee Distributors offer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System M4 chargers for charging System M4 battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
The following battery packs can be charged with this charger:
voltage
battery
rating
(of storage battery)
4 V
M4B2
2.0 Ah
Do not try to charge non-chargeable batteries with this charger.
No metal parts must be allowed to enter the battery section of
the charger (short circuit risk).
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Do not touch the tool with conducting objects.
Never charge a damaged battery pack. Replace by a new one.
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by
authorised Service Agents.
This appliance is not intended to be
used or cleaned by persons with
reduced physical, sensory or mental
capabilities, or lack of experience or
knowledge, unless they have been
given instructions concerning the
safe use of the appliance by a
person legally responsible for their
safety. They should be supervised
whilst using the appliance. Children
shall not use, clean or play with this
appliance, which when not in use
should be secured out of their reach.
Warning! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater, certain
industrial chemicals, and bleach or bleach containing products,
etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The battery screwdriver is designed for drilling and screwdriving
for independent use away from mains supply.
The quick charger can charge Milwaukee batteries from
M4 to 4 V.
Do not use this product in any other way as stated for normal
use.
MAINS CONNECTION M4 C
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also possible
to connect to sockets without an earthing contact as the design
conforms to safety class II.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under "Technical Data" fulfills all the
relevant regulations and the directives 2011/65/EU (RoHS),
2014/30/EU, 2006/42/EC, and the following harmonized
standards have been used:
EN 62841-1:2015
EN 62841-2-2:2014
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-12-15
No. of
battery
cells
1
Alexander Krug
Managing Director
Authorized to compile the technical file.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under "Technical Data" fulfills all the
relevant provisions of the following Regulations S.I. 2008/1597
(as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as
amended) and that the following designated standards have
been used:
BS EN 62841-1:2015
BS 62841-2-2:2014
BS 55014-1:2017+A11:2020
BS 55014-2:2015
BS IEC 63000:2018
Winnenden, 2020-12-15
Alexander Krug
Managing Director
Authorized to compile the technical file.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
ADVICE FOR OPERATION
Never use the gear switch whilst the machine is operating. Only
use the switch when the machine is at a standstill.
BATTERIES
Battery packs which have not been used for some time should
be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to
heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
ENGLISH
19
Publicité
