Sommaire des Matières pour Star Ultra Max UM1854-NATCE
- Page 1 ® CONVEYOR OVEN MODEL UM1854-NATCE Installation and Operation Instructions 2M-Z6832 Rev. D 4/17/2006 UM1854...
- Page 2 RETAIN THIS MANUAL FOR FUTURE REFERENCE NOTICE Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability. Star reserves the right to change specifi cations and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.
- Page 3 SPECIFICATIONS UM1854-NATCE Gas Rating/Connection: 11.72kW (40,000 BTU/hr), 1/2" BSP female pipe connection Country: AT, DK, FI, IE, HU, PT LU, DE BE, FR ES, SE, GB, IT, CH, CR Gas Category: Pressure (mBar): @20/25 Electrical Supply: 220-240v, single phase, 1.2A (max), 50Hz Approximate Weight (Single Oven with Cart): Installed - 280 Lbs (127.27 kg), Shipping - 350 Lbs (159.09 kg) Dimensions: Width: 60.6"...
- Page 4 This appliance must be installed with a stand and This equipment is designed and sold for commercial casters designed by Star Manufacturing as part of a use only by personnel trained and experienced in its complete installation. The installation must also include operation and is not sold for consumer use in and a connector complying with either ANSI Z21.69 or CAN/...
- Page 5 Star Service Representative. control chamber on the right side of the oven is This service is required by Star in order to assist required. Do not obstruct the ventilation holes in the the purchaser in proper start-up of the oven on site.
- Page 6 VENTILATION LOCATION A VENT IS REQUIRED: Local codes prevail. These The well-planned and proper placement of your oven are the "authority having jurisdiction" as stated by the will result in long-term operator convenience and National Fire Protection Association, Inc. in NFPA satisfactory performance.
- Page 7 3. Insert candle through conveyor tunnel or oven amperage, and phase requirements stated on the door. (Use Star Smoke Candle 2W-Z5668.) rating plate. A wiring diagram is included herewith. 4. Light the fuse of the smoke candle and immediately...
- Page 8 Installation must conform with local codes or, in the Stacked Oven Install Preparation: absence of local codes, with NFPA54/ANSI Z223.1 1. Remove door, conveyor, and fi nger assemblies. - Latest Edition. 2. Unbolt unit from shipping crate (4 bolts). 3. Turn unit on front as shown. CAUTION 4.
- Page 9 HOLLOW WALL STUD OR MASONRY WALL CAUTION RESTRAINT REQUIREMENT 1. The installation shall be made with a gas connector DO NOT WORK AROUND THE CONVEYOR that complies with local codes for connectors for BELT WITH LONG HAIR, LOOSE CLOTHING, movable gas appliances and a quick-disconnect OR DANGLING JEWELRY.
- Page 10 Please take time to read the following safety To adjust the time and temperature: operating instructions. They are the key to the 1. Press the DOWN and UP arrows ( ) at the successful operation of your Ultra-Max Conveyor same time. Hold for four seconds until the TIME Oven.
- Page 11 DISPLAY INFORMATION after reaching the STORE level. yES indicates When operating the oven, there are three levels that the parameters cannot be changed even after entering the STORE level. The LOC setting can of access: 1. Store Level - General employees would know be toggled using the ENTER button ( these functions and how to change them.
- Page 12 BAKE TIME VERSUS TEMPERATURE CONVEYOR SPEED 1. Bake time is actually conveyor speed and is defi ned Bake Time (Conveyor Speed) - As stated previously, as the time the product is actually in the oven. bake time (conveyor speed) is defi ned as the amount This is measured by noting the time when the of time elapsed between the time the leading edge of leading edge of the product enters the oven and...
- Page 13 If maintenance is required, contact your local local and national health standards. service company, a factory representative, or Star Manufacturing. CAUTION If the gas oven needs to be moved, the gas must be turned off and disconnected from the unit before moving the restraint.
- Page 14 DIRECTIONS FOR DISASSEMBLY 1. Remove crumb trays and 2. Push the spring-loaded 3. Lift up the left end of the shelves from both ends. coupling in to disengage the conveyor frame so the crumb pin in the shaft. Rotate the tray supports clear the tunnel shaft so the pin will not go opening.
- Page 15 CONVEYOR BELT TENSION The conveyor belt of the Ultra-Max Gas Conveyor Oven does not have a tension adjustment. If the belt becomes too loose, a link will have to be removed to tighten. A belt that is too tight will also cause operational problems due to excessive drag.
- Page 16 “start-up/check-out has been performed by a Factory Authorized Technician. In order to make a claim under this warranty; a warranty report must be fi led with Star Manufacturing International Inc. in St. Louis, Missouri, U.S.A. by the dealer/distibutor through which product was purchased. All details, including serial number and model num- ber of the defective unit, must be included.
- Page 19 ADAPTER 1/2 NPT TO 1/2 BSP (FEMALE) 2E-Z6875 METAL OXIDE VARISTOR IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. Star Manufacturing International, Inc.
- Page 21 PLUG CAP 2M-Z5569 INSTRUCTION LABEL IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. Star Manufacturing International, Inc.
- Page 23 UPPER FINGER WELDMENT G9-Z5648 UPPER FINGER BAFFLE IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. Star Manufacturing International, Inc.