Pattfield Ergo Tools E-HS 660 Mode D'emploi page 13

Anleitung E-HS 660_SPK7:Anleitung HS 580 SPK 1
29. It is advisable not to use the hedge trimmer
when other persons, and particularly children,
are nearby.
30. Children are not allowed to use the hedge
trimmer.
31. Noise at the workplace may exceed 85 dB(A).
In this case, the operator must wear ear-muffs
or similar.
32. Vibrations on the handle were measured in
accordance with EN 50144-2-15.
33. Please use an RCD with this unit.
2. Layout (see Fig. 1)
1. Cutter
2. Hand guard
3. Guide handle with switch button
4. Handle with switch buttons above and below
5. Cable holder
6. Power cable
7. Cutter guard
8. Impact guard
9. Trimmings collector
10. Fastening screws for trimmings collector
Important! You must never use the hedge trim-
mer without wearing gloves.
3. Explanation of the plate (see Fig. 3)
1. Warning
2. Keep out of the rain and protect from getting wet.
3. Read the operating instructions before using for
the first time.
4. Pull the plug from the power supply immediately
if the cable gets damaged or severed.
5. Wear goggles and ear muffs.
4. Technical data
Voltage 230V ~ 50Hz
Power consumption
Cutting length
Cutter rail length
Tooth spacing
Cuts/min
Sound power level LWA
Sound pressure level LPA 88,6 dB(A)
Vibration aw
Weight
5. Voltage
The machine can only be run on single-phase alter-
nating current with 230V ~ 50Hz a.c. voltage. Before
you use the machine for the first time, check that the
mains voltage is the same as the operating voltage
shown on the machine rating plate.
6. Using for the first time and operation
Important! This hedge trimmer is designed for the
trimming of hedges, bushes and shrubs. If it is used
for any other purpose not expressly permitted by
these operating instructions there may be a risk of
damage to the hedge trimmer or serious injury to the
user. The hedge trimmer comes with a two-hand
safety switch. It only works if the switch on the guide
handle (Fig. 2 / Item 1) is pressed with one hand and
either the switch on top of the handle (Fig. 2 / Item 2)
or the switch below the handle (Fig. 2 / Item 3) is
pressed with the other hand.
Releasing any of the switches will bring the hedge
trimmer to a stop.
In so doing, please check the running of the
blades.
- Please check that the blades function correctly.
The blades cut on both sides and run in opposite
directions to each other, for guaranteed high
cutting performance and quiet operation.
- Fasten the extension cable to the cable holder
before starting to use the machine (see Fig. 4).
- For use in the open air you must only use
extension cables certified for the purpose.
b Attaching the trimmings collector (Fig. 11/12)
Place the trimmings collector on the cutter rail
(Fig. 11). Then slide the trimmings collector
towards the tip of the cutter as far as the stop
and tighten the fastening screws (A) (Fig. 12).
The trimmings collector can be fitted either on the
left-hand or the right-hand side.
600 W
530 mm
600 mm
7. Tips on use
20 mm
b The hedge trimmer can be used not only for trim-
3200/min
ming hedges but for trimming shrubs and bushes
96 dB(A)
as well.
For optimum trimming performance, guide the
b
3,3 m/s 2
blade teeth at an angle of approx. 15° to the
hedge (see Fig. 5).
4,0 kg
12.12.2007 15:41 Uhr Seite 13
GB
13