Publicité
Les langues disponibles
Les langues disponibles
GB
FR
DE
ES
SPECIAL SAFETY RULES
Wear ear protectors. Exposure to noise can cause
■
hearing loss.
Use auxiliary handle(s), if supplied with the tool.
■
Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces,
■
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a «live» wire may make exposed
metal parts of the power tool «live» and could give the
operator an electric shock.
ASSEMBLY
AUXILIARY HANDLE ASSEMBLY
See Figure 2.
An auxiliary handle is packed with the drill for ease of
operation and to help prevent loss of control. The handle
can be mounted on the opposite side for left or right hand
use.
Insert handle screw into hole located above trigger
■
switch and seat hex head into hole.
Slide handle collar onto screw, seat hex end of collar
■
into hex hole. Hex hole for depth stop rod should be
on top of collar.
Slide depth stop rod into hex shaped hole on top of
■
collar.
Slide depth guide clamp into notch in collar. Clamp
■
holds depth rod firmly in place.
NOTE: When properly installed, the teeth on the depth
stop rod should be aligned with the teeth indicator on the
depth stop rod clamp.
Thread auxiliary handle onto screw and secure tightly.
■
NOTE: Be sure the auxiliary handle is securely tightened
against the depth stop rod clamp. This secures the depth
stop rod at the desired depth of cut. It also secures the
auxiliary handle.
DESCRIPTION
1.
Keyless chuck
2.
Torque adjustment ring
3.
Quick mode selector
4.
Two-speed gear train
5 . Rotation selector (forward/reverse/center lock)
6.
Depth rod stop
7.
Bit storage
8.
Switch trigger
9.
Mag Tray™
10. Handle screw
11. Hex head hole
12. Handle coller
13. Teeth
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
English
14. Depth stop rod clamp
15. Auxiliary handle
16. Battery pack (Not included)
17. Latches
18. Depress latches to release battery pack
19. Reverse
20. Forward
21. Chuck jaws
22. Lock (tighten)
23. Unlock (release)
24. Low speed
25. High speed
26. Drive mode
27. Drill mode
28. Hammer mode
29. To increase torque
30. To decrease torque
31. Bit
32. Screws
33. Bit holder
34. Drilling depth
35. Drill bit
36. Scale
37. To increase drilling depth
38. To loosen
39. To tighten
40. To decrease drilling depth
41. Chuck sleeve
SPECIFICATIONS
Voltage
Chuck
Switch
No load speed (Drill mode):
-Lo speed
-Hi speed
Hammer speed (Blows per minute):
-Lo speed
-Hi speed
Max. torque
Weight (not incl. battery pack)
MODEL
LCDI1802
1
HU
RO
LV
LT
EE
BATTERY
PACK
(not included)
BPL-1820
BPL-1815
BPP-1815
BPP-1815M
BPP-1817
BPP-1817M
HR
SI
SK
GR
TR
18 V
2-13 mm
Variable speed
-1
0-400 min
-1
0-1500 min
-1
0-5200 min
-1
0-19500 min
49 Nm
1.68 Kg
COMPATIBLE
CHARGER
(not included)
BCL-1800
BCS618
BCL1418
BCL14181H
BCL14183H
BC-1815S
BC-1800
BCL-1800
BCS618
BCL1418
BCL14181H
BCL14183H
Publicité
