Publicité
Déballage de votre ensemble de clôture
Lors du déballage de votre ensemble de clôture, vérifiez que tous les composants illustrés sur cette page sont
inclus. Faites attention lorsque vous déballez votre ensemble de clôture pour éviter d'endommager les composants.
Installing Your SawStop Premium Fence Assembly
Before assembling your Premium Fence
• Locate the front rail, the rear rail, and the fence assembly
• Take the front rail (the larger of the two rails) and align it to
hardware pack. All of the hardware needed to install the fence
the front edge of your saw by centering the notches in the rail
Assembly, make sure that you have all the
system is located on the fence assembly hardware pack. In
with the two miter slots in the table and aligning the two holes
necessary components identified on page 1
order to easily identify the hardware used in each of the
between the notches with the two corresponding holes in the
front edge of the table. Aligning the two holes between the
in the owner's manual, including the fence
following steps, the different pieces of hardware are numbered
notches aligns all the other holes used in mounting the front
on the hardware pack and in the figures.
assembly hardware pack. Call the SawStop
rail to your saw; different holes are used for different saws.
Service Department at 503-582-9934 if any
Note: Your saw must be fully assembled before installing the
When the holes are aligned, mount the front rail to the saw by
fence system.
taking four M8x1.25x16 flat head socket bolts
components are missing. You will also need
one into each of the four threaded holes in the front edge of
the following tools to complete the fence
the main table. Tighten the four bolts using a 5 mm hex key.
assembly installation:
Fence Assembly Hardware Pack
front rail
Flat Head Socket Bolts,
1. a 3 mm hex key
M8x1.25x16 (8)
1
M8 (15 + 1 extra)
Lock Washers,
4
2. a 5 mm hex key
Flat Head Socket Bolts,
M8x1.25x25 (8)
2
M8x1.25 (8)
Hex Nuts,
5
3. a 13 mm wrench
1
4. a straight-edge
Hex Head Bolts,
1
M8x23x2 (15 + 1 extra)
Washers,
3
M8x1.0x16 (7)
6
2
• Use a straight-edge to level the front edge of the left
• Take the rear rail (the smaller of the two rails) and align it to
• Take two M8x1.25x25 flat head socket bolts
extension wing to the cast iron table top. You may have to pull
the rear edge of your saw by centering the notches in the rail
one through the open hole at the end of each extension wing.
up or push down on the outer edge of the extension wing to
with the two miter slots in the table and aligning the left-most
Place an M8x23x2 washer
hole between the notches with the corresponding hole in the
the back of each of bolt and then thread an M8x1.25 hex nut
level it. Once the front edge of the left extension wing is level,
rear edge of the table. There are three holes in the rail
on each bolt. Hand tighten the nuts; do not fully tighten them.
use a 5 mm hex key and a 13 mm wrench to fully tighten the
nut on the bolt that mounts the left extension wing to the front
between the notches, one solitary hole and two holes paired
rail. Repeat this process to level the front edge of the right
together, and the left-most hole is the solitary hole. Not all of
extension wing.
the holes are used to mount the rail to your saw; different
straight-edge
holes are used for different saws. Aligning the left-most hole
aligns all the other holes used in mounting the rear rail to your
saw. When the holes are aligned, mount the rear rail to the
saw by taking four M8x1.25x16 flat head socket bolts
1
and
2
threading one into each of the four threaded holes in the rear
edge of the main table. Tighten the four bolts using a 5 mm
hex key.
level the extension
wing and tighten the
nut on this bolt
5
6
7
1
align the left-most
WARNING
Moving
can
Do
!
pinch,
gears
and
hole between
door
not
with
open.
or crush.
cut
operate
parts
the notches
affiche des instruc-
tions d'installation
rail avant
rail arrière
tube principal
SawStop Service Department
503-582-9934
www.sawstop.com
© SawStop, LLC
• Take two M8x1.25x25 flat head socket bolts
2
and insert
• Place an M8x23x2 washer
3
and an M8 lock washer
4
on
one through the open hole at the end of each extension wing.
the back of each of the M8x1.25x25 flat head socket bolts
2
that extend through the extension wings, and then thread an
M8x1.25 hex nut
on each bolt. Hand tighten the nuts; do
5
not fully tighten them.
5
4
3
1
and threading
2
2
2
miter slots
3
4
notches
2
and insert
• The next step of the assembly is easiest with two people.
level the extension
Position the extension table between the front and rear rails.
wing and tighten the
3
and an M8 lock washer
on
nut on this bolt
4
Make sure that the table is oriented so that the adjustment
5
bracket is closest to the right extension wing. Tilt the extension
straight-edge
table slightly so that the adjustment bracket can fit under the
edge of the extension wing. Position the extension table so
that the end of the adjustment bolt aligns with the
2
corresponding threaded hole in the bottom of the extension
wing. With the weight of the extension table still supported,
4
turn the adjustment bolt until the extension table is roughly
2
3
5
flush with the extension wing.
adjustment
bracket
or
parts
and
crush.
!
can
WARNING
Do
pinch,
not
Moving
door
operate
with
open.
gears
cut
• Use a straight-edge to level the rear edge of the left
extension wing to the cast iron table top. You may have to pull
up or push down on the outer edge of the extension wing to
level it. Once the rear edge of the left extension wing is level,
8
9
adjustment
bracket
use a 5 mm hex key and a 13 mm wrench to fully
adjustment
bolt
tighten the nut on the bolt that mounts the left
poignée de clÔture
SawStop
®
Premium Fence Assembly
OWNER'S MANUAL
le manuel du
propriétaire
Ensemble de clôture premium SawStop 1
table à rallonge
guide longitudinal
premium
Fence Assembly Hardware Pack
Flat Head Socket Bolts,
1
M8x1.25x16 (8)
Lock Washers,
4
M8 (15 + 1 extra)
Flat Head Socket Bolts,
2
M8x1.25x25 (8)
Hex Nuts,
5
M8x1.25 (8)
Washers,
Hex Head Bolts,
3
M8x23x2 (15 + 1 extra)
M8x1.0x16 (7)
6
pack matériel
Publicité
