EDM Product 08761 Manuel D'instructions page 36

Chain saw
Features
Sound and vibration
Measured sound values determined according to EN
60745-2-13:2009+A1:2010.
Vibration total values (triax vector sum) determined
according to EN 60745-2-13:2009+A1:2010. The vibration
emission level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745-2-13:2009+A1:2010 and may be used to compare
one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for
different applications, with different accessories or poorly
maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work
patterns.
Keep the noise emissions and vibrations to a minimum
• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch off the tools when it is not in use.
• Wear protective gloves.
Battery charger
The lithium-ion battery can be charged at any time and will
not develop a "memory" when charged after only a partial
discharge. It is not necessary to run down the battery pack
charge before recharging. Remove the battery pack from
the tool when convenient for you and your job. You can
"top-off" your battery pack's charge before starting a big job
or long period of use.
Due to lithium-ion's fade-free properties, the only time it is
necessary to charge the lithium-ion battery pack is when
the pack has reached the end of its charge. To signal the end
of charge, power to the tool will drop quickly. Charge the
battery pack as needed.
Charging the battery
This lithium-ion battery pack is shipped partially charged.
Before using it the first time, fully charge the battery pack. A
fully discharged battery pack with a temperature between
5°C and 35°C will charge in about 1 hour(See section"
technical data").
• Plug the charger adapter into power source. The green
light on the charger stand will illuminate, indicating
EN INSTRUCTION MANUAL
the charger is powered.
• Slide the battery all the way into the charger stand until it
locks in place with a click. The red light on the
charger stand will illuminate, indicating that the battery is
charging.
• The red light will go off after charging is complete and a
green light will appear.
NOTE: Batteries may become warm while charging. This is
normal. If the battery is hot after continuous use in the tool,
allow it to cool down to room temperature before charging.
This will extend the life of your batteries.
WARNING: Always disconnect the battery pack from the
tool before any assembly, adjustments or changing
accessories.
b. Insertion and removal of rechargeable battery (Fig.2)
Depress the battery-release button located on the front of
the battery pack to release battery pack. Pull the battery
pack out and remove it from the tool.
Chain saw assembly
Note: After unpacking, check the contents for completeness
and possible transport damage.
If a part is missing or damaged, please contact the seller.
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty period
has expired.
Installation: Installing the guide bar and saw chain
WARNING!
• The teeth of the saw chain are very sharp!
Protective gloves must be worn during all work
on the chain.
Risk of injury!
• An incorrectly installed saw chain leads to uncontrolled
cutting behaviour by the device! When fitting chain,
observe the prescribed running direction!
• Place the chainsaw on a level surface.
REF. 08761