Safety Instructions - Senco SRT25 Mode D'emploi

Disposal of batteries
Batteries contain substances that can be harmful
to human health and the environment if they are
not handled properly� Batteries are marked with the
crossed trash bin� It symbolises that waste batteries
must not be disposed with unsorted waste but must
be collected separately�
It is important that you hand in your waste batteries to
the collection points that are established. In this way,
you help to ensure that the batteries are recycled in
accordance with legislation and do not unnecessarily
damage the environment� Your local waste authori-
ties can inform you how to dispose and recycle this
type of battery correctly.

Safety instructions

WARNING! To avoid serious injuries to persons or
property, please read these safety instructions care-
fully and make sure you understand them.
!
Points of attention when using the rebar
tying tool
Using the rebar tying tool for other purposes or other
applications than described in this manual can result
in serious accidents. Please make sure that you fol-
low all instructions in the manual� People who have
nothing to do on the work site, especially children,
should be kept out of the work site and should not
have access to this equipment�
Use appropriate protection gear.
Employer and operator must make sure that the
operator uses proper eye protection when the tool is
used� This protection must comply with current laws
and norms�
NB: Glasses without side protection and single-sided
protection screen do not provide adequate protection�
Earmuffs can be necessary.
On a lot of work sites, it can be necessary to wear
earmuffs, to avoid permanent damage to the hear-
ing� Employers and employees must make sure that
proper earmuffs can be found and is used on the
work site�
No children near the rebar tying tool.
Do not allow spectators, especially children, near the
machine while working with it�
Do not use the rebar tying tool near flammable
substances.
Never use the rebar tying tool near any flammable
substances or fumes. The fumes from these can be
sucked into the engine and cause an explosion.
Do not use the rebar tying tool in wet or damp
environments.
If the rebar tying tool is used in direct rain or water,
damp environments or similar, the risk of getting an
electrical chock is increased� Do not leave the rebar
tying tool where it can be exposed to this.
Check the parts of the rebar tying tool before
sliding in the battery.
Check that all screws are tightened properly� Im-
proper tightening of screws can result in an accident
or breakage� Make sure that all parts are intact� Parts
will be worn out over time� Check also that no parts
are damaged, defective or worn. If parts are missing
or need to be repaired, contact your dealer immedi-
ately. Use only parts approved by the manufacturer.
Set the main switch in OFF position and lock the
trigger when changing the battery or changing/
adjusting the wire coil. Remove the battery if an
error occurs and the machine cannot be used.
If the machine is left on, it may cause damage.
Keep clear of the nose, feeding gears and wire
coil during use of the rebar tying tool.
DO NOT hold your fingers near the nose or other
moving parts as the wire and moving parts easily can
cause damage�
Keep clear of the machine mouth during use of
the rebar tying tool.
Do not touch the wire or the machine mouth when the
machine is tying� You may get caught in the wire loop
and suffer serious injury.
Do not point the rebar tying tool towards others
during use.
People can get hurt if they are caught in the machine
during use. When tying, be careful and stay clear of
the moving parts�
Do not touch the trigger unless you have to.
When carrying the rebar tying tool and when not ty-
ing, remember to set the main switch in OFF position,
and lock the trigger. If not, you will risk activating the
rebar tying tool unintentionally and cause a danger-
ous situation�
Do not use the rebar tying tool during a malfunc-
tion.
If the rebar tying tool does not work correctly, set
the main switch in OFF position, lock the trigger and
remove the battery before checking what is wrong.
If necessary, contact your dealer and have the rebar
tying tool repaired�
EN
7