Mestra KOALA Mode D'emploi page 12

English
the other steps are empty and they will
not run.
2. Select Operating Mode (Mixing, Vacuum
and Vacuum+Mixing) pressing Selection
Key (7).
3. Select wanted time pressing Up/Down
Keys (2) and (3). If there is no Operating
Mode selected
Keys will block.
4. If you want that after running this step
the machine stops (Programme with
stop), press Start/Stop Key. The light
corresponding to Operating Mode (8), (9)
or (10) will light off and on quickly,
indicating that after this cycle the
programme will pause. To erase the
pause, press "Start/Stop" Key and the
corresponding light will stop flickering.
5. Press Programme Key to memorize the
cycle and continue with the next one.
The display will show "PX-2". Repeat
previous steps to finish cycles "PX-2"
and "PX-3".
6. When we programme a cycle, for
instance No. 1, and we want to finish and
conclude the programme, we just have
to press Programme Key for 3 seconds.
The rest of cycles will erase finishing this
way edition, showing the display "End".
It is possible to run at any moment
programmes stored in memory. For this,
when the machine is in stand-by:
1. Press "Programme" Key (4). The
display will
programme.
2. Select with "Up/Down" Keys (2) and
(3) the programme number that you
want to be run.
3. Press "Start/Stop"
machine will
programme.
PROGRAMMING EXAMPLES
Example 1
Suppose you want to edit Programme No. 3
so that the following cycle runs:
An initial step of only "Vacuum" for 10
•
seconds.
A second step of "Vacuum + Mixing" for
•
1 minute.
This programme example has an interesting
practical use that allows fixing the bowl to
the mixer some seconds before the mixing,
so operation is more convenient.
12
previously, Up/Down
show the last
Key (5). The
run the selected
1. Press "Programme" Key. The display will
show the number of the last run
programme.
2. Press "Up/Down" Keys (2) and (3) until
"Pr-3" is showed.
3. Press "Programme" Key again for 3
seconds. You will know you are in
programming mode because the display
shows "P3-1" flickering.
4. Press "Selection" Key till the "Vacuum"
Mode light lights.
5. Select 10 seconds with "Up/Down" Keys.
6. Press "Programme" Key. "P3-2" will
appear on the display indicating we are
in Programme 3 step 2.
7. Press "Selection" Key till "Vacuum +
Mixing" Mode light lights.
8. Select 1 minute with "Up/Down" Keys.
9. Press "Programme" Key for approx. 3
seconds." End" will appear on the display
and the machine would go back to stand-
by mode. The programme is now stored
in memory.
Example 2
Suppose you want to edit Programme No. 5
so that the following cycle runs:
An initial step of only "Mixing" for 45
•
seconds. After this step, the Mixer stops
so that the user can handle the mixture.
Then, the user should place the bowl
again and press "Start/Stop" key, and the
machine will continue the cycle.
run A second step of "Vacuum" for 10
•
seconds. This makes easier placing the
bowl on the Mixer.
A third step of "Mixing + Vacuum" for 1
•
minute. Once it finishes the cycle is
ends.
Programming
follows:
1. Press "Programme" Key. The display will
show the number of the last run
programme.
2. Press "Up/Down" Keys (2) and (3) until
"Pr-5" is showed.
3. Press "Programme" Key again for 3
seconds. You will know you are in
programming mode because the display
shows "P5-1" flickering.
4. Press "Selection" Key till the "Mixing"
Mode light lights.
5. Select 45 seconds with "Up/Down" Keys.
sequence should be as