Publicité
Les langues disponibles
Les langues disponibles
633872
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting
to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-related
hazards.
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool's operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation.
WARNING: When used in Australia or New Zealand, it is recommended that this tool is ALWAYS
supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.
Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Electric Water Butt Pump Safety
• WARNING: If you use an extension lead, ensure the extension connections are protected from
exposure to rain and/or water discharged by the pump.
• The pump must always be transported, used, submerged, and stored, vertically. Carry the pump
only by the lifting handle. Never carry, lift or submerge the pump by its power cable
• NEVER use this pump when ambient temperatures are close to freezing
• DO NOT attempt to operate the pump below the minimum water level as this will cause
permanent damage
• This pump must be operated exclusively on power points that are protected by an RCD with a
maximum tripping current of 30mA and a maximum delay of 40ms
• The electrical supply should be the same as detailed on the pump casing.
• DO NOT use this pump in swimming pools or ponds that are occupied. When in operation, the
area around the pump should be clear of all people and animals.
• Ensure hands are dry whenever connecting or disconnecting the plug from the power supply.
• When using the pump after prolonged periods of storage, first check the pump casing and cable
for any obvious signs of damage. If in doubt, consult a qualified electrician.
• Protect the cable and plug from exposure to oil, excessive heat, and sharp objects
• Never place excessive strain on the cable as this could weaken its connections to the pump and/
or power plug
• Do not allow children to touch the product or any of its components
• This pump is designed for use in clean water environments but will discharge, in the liquid,
suspended solids no larger than 3mm diameter
• DO NOT use this pump with substances other than water
• Sand and other abrasive materials present in the liquid being pumped will cause increased wear.
• Where possible, avoid using the pump continuously for more than 10 minutes
• This pump is designed for domestic applications only, in and around the home and garden. Do
Water Butt Pump 400W
not use in a commercial or industrial environment as the pump is not designed for heavy-duty
use. It is designed for periodic on/off cycles, not for long-term continuous operation.
• Do not use with liquid that has a temperature greater than 35°C.
• Dry running of the pump creates excessive wear and must be avoided.
• When not in use, protect the pump from frost damage and store in a dry place.
• ALWAYS observe local laws and regulations when connecting submersible pumps to the power
supply. Consult a qualified electrician when necessary
Product Familiarisation
1.
Exit Pipe
2.
Suspending Arm
3.
Extension Pipe
4.
Carrying Handle
5.
Suction Base
6.
Pump Unit
7.
Male Quick Connector
8.
Shut-Off Valve
Intended Use
• Electric water butt pump, for pumping water from a water butt. Maximum submersible depth
of 8m, with filtration to prevent blockages, provides usable collected water at a flow rate of
41.6ltr / min
Unpacking Your Tool
• Carefully unpack and inspect your new tool. Familiarise yourself with all its features and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Pipe assembly
• Position the Pump Unit (6) on a secure flat surface, in preparation for assembly
• Take the Connecting Pipe (3) and fasten the female connector on to the threaded male orifice
located at the top of the Pump Unit
• To fasten the Exit Pipe (1) to the Connecting Pipe, screw the female connector on to the male
threaded end of the Connecting Pipe
Suspending arm adjustment
Note: The height of the suspending arm should correspond with the depth of the Water Butt. Use
the suspending arm to support the pump against the side of the collection tank.
• To adjust the height of the Suspending Arm (2), unscrew the plastic nut immediately above the
arm, then re-position and tighten the nut
Hose connection
Attach a female hose quick connector (not included) to the garden hose, and push-fit onto the Male
Quick Connector (7)
Operation
Note: If the base of the water container is lined with small particles, dirt, or debris, use the
Suspending Arm (2) to lift the pump unit away from the floor.
Switching on and off
• Ensure that the pump is situated in a secure location, inside the water container, with the Pump
Unit (6) entirely submerged
• Plug the power cord into the mains power socket
• Switch the mains on. The pump will start automatically
• To switch the pump off, switch off at the mains
silverlinetools.com
5
Publicité
