BRAND
SnapSkru MINI SPM
®
Self-Drilling Drywall Anchor
• Makes only 1/4" hole — small head hides behind fixture
• Holds over 80% more than other self-drilling drywall anchors
• Activates & locks with audible "pop" indicating correct installation
• Positive stop prevents overturning — does NOT destroy drywall
• Needs only a #2 Phillips screwdriver or screw gun — no drill or
special tools required
Securely hang bathroom accessories, mirrors, picture frames, lighting
fixtures, drapery, smoke detectors, alarms, thermostats, shelving,
electric boxes ...
SnapSkru MINI SPM Anchor Installation
Instructions in Drywall 3/8" to 5/8" Thick
1. Press tip of SnapSkru MINI anchor into drywall using #2 Phillips
screwdriver or screw gun. Drive anchor clockwise into drywall until
anchor stops flush with wall.
2. Place item over anchor and insert screw. Use any sheet metal
screw from #6 - #8 (#6 preferred), with minimum thread length 1"
plus the thickness of the item being anchored.
3. Tighten screw flush with item. Screw "pops" open anchor, locking
anchor on wall.
TOGGLER® BRAND anchors are made in the U.S.A. Patented under one or more of U.S. Patent Nos. 5,161,296; 6,161,999; and 7,144,212; and foreign counterparts thereof and of 4,650,386 and 4,752,170. Other patents pending. TOGGLER and typeface, ALLIGATOR, SNAPTOGGLE, and SnapSkru are worldwide registered trademarks of
Mechanical Plastics Corp. AF8, BB, SP, and SPM are worldwide trademarks of MPC.
BRAND
SnapSkru SP
®
™
Self-Drilling Drywall Anchor
• Holds over 80% more than other self-drilling drywall anchors
• The only one that locks on the wall — resists shock & vibration
• Activates & locks with audible "pop" indicating correct installation
• Positive stop prevents overturning — does NOT destroy drywall
• Needs only a #2 Phillips screwdriver or screw gun — no drill or
special tools required
Securely hang bathroom accessories, mirrors, picture frames, lighting
fixtures, drapery, smoke detectors, alarms, thermostats, shelving,
electric boxes ...
SnapSkru SP Anchor Installation
Instructions in Drywall 3/8" to 5/8" Thick
1. Press tip of SnapSkru anchor into drywall using #2 Phillips
screwdriver or screw gun. Drive anchor clockwise into drywall until
anchor stops flush with wall.
2. Place item over anchor and insert screw. Use any sheet metal
screw from #6 - #10 (#8 preferred), with minimum thread length
1-1/4" plus the thickness of the item being anchored.
3. Tighten screw flush with item. Screw "pops" open anchor, locking
anchor on wall.
™
1
2
3
© 2007 MPC
1
2
3
ALLIGATOR AF8
TM
Solid-Wall Anchor
• Out-holds all metal, adhesive, epoxy, and chemical
anchors with the same screw diameter & embedment —
NOT A HOLLOW PLASTIC PLUG!
• Anchor bonds screw to concrete & masonry, sealing hole
• Resists vibration and shock in both solid & hollow walls —
anchors securely even if it hits a hidden cavity
Securely hang lighting fixtures, brackets, shelving, alarms,
electrical equipment, handrails, plumbing fixtures, signs...
ALLIGATOR AF8 Anchor Installation Instructions
1. Drill 5/16" diameter hole – minimum hole depth 2".
Insert anchor and tap flush with wall.
2a. Place item over anchor. Insert screw and tighten flush.
For best results use screw gun for installation in solid
walls.
2b. In walls of minimum thickness 1/2", screw opens
anchor and locks securely.
pop!
For technical bulletins & where to buy, visit www.toggler.com
NOTE: Industry safety standards recommend 1/4 of ultimate test load.
™
TM
SNAPTOGGLE BB
Heavy-Duty Hollow-Wall Anchor
• Holds 2x as much as old-fashioned wing toggles
• Small 1/2" installation hole — smallest hole for 1/4" bolt
• Fast — use a screw gun — anchor does not spin
• Anchor preinstalls without the bolt
Securely hang flat panel TVs, window treatments, grab bars,
lighting fixtures, cabinets, partitions, shelving, heavy fans,
sinks, garage doors, DSS antennae, reinstallations...
SNAPTOGGLE BB Anchor Installation Instructions
1. Drill 1/2" hole. Hold metal channel flat alongside plastic
straps & slide channel through hole. Minimum clearance
behind wall only 1 7/8".
2. Hold ends of straps together between thumb & forefinger
and pull toward you until channel rests behind wall.
Ratchet plastic cap along straps with other hand until
flange of cap is flush with wall.
pop!
3. Place thumb between straps at wall. Push thumb side to
side, snapping off straps level with flange.
4. Place item over flange. Insert bolt and tighten until snug
against item, then stop. Use 1/4"-20 machine screw.
BRAND
®
™
BRAND
1
®
™
2
3
4
P/N 62727 · Rev A (06/07)
1/2" diameter
Must be 1-7/8" minimum clearance
behind wall for channel rotation
3/8" to 3-5/8"
Thick