Reer BABYPHON MIDI FD-2600 Mode D'emploi page 14

BUTTONS:
01. Antenna
02. Channel A/B LED
03. Sensitivity levels -LED
04. Microphone
05. ON/OFF - button
06. POWER/STANDBY battery check light
07. Strap connection
08. Button "UP"
09. „M"-button
10. Button "DOWN"
11. Plug
12. Battery compartment
13. Reset-button
ANTENNA:
The antenna is permanently and secu-
rely attached and cannot be extracted.
For optimal reception please place unit
in an upright position.
RESET-BUTTON:
Use the Reset-button (13) only in the
event that the unit is unresponsive or
not functioning properly. Use the tip
of a pen, a paper clip, or a needle and
gently push the Reset-button on the
back of the enclosure.
The Reset-button will restore the unit's
default settings.
NOTE:
Adjust the level of sensitivity according to
your individual requirements; the manufactu-
rer recommends setting the level to medium
during the day and to low at night.
NOTE:
Only the included batteries are rechargeable
in the Babyfone unit itself!
3004.indb 14
All manuals and user guides at all-guides.com
ON-/OFF-BUTTON: ON-/OFF-BUTTON: ON-/OFF-BUTTON:
The Sender unit's ON-/OFF-BUTTON is the main power switch and turns on the entire unit. The Sender unit's ON-/OFF-BUTTON is the main power switch and turns on the entire unit. The Sender unit's ON-/OFF-BUTTON is the main power switch and turns on the entire unit.
LED DISPLAY CHANNEL A/B:
The unit can be operated on two different channels in order to avoid interfe- The unit can be operated on two different channels in order to avoid interfe- The unit can be operated on two different channels in order to avoid interfe-
rences. These channels are individually adjustable. Hold down the „M"-button rences. These channels are individually adjustable. Hold down the „M"-button rences. These channels are individually adjustable. Hold down the „M"-button
until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the until channel ‚A' or ‚B' starts flashing. Now select the
select a channel. Push the "M"-button again to confirm. SENDER and select a channel. Push the "M"-button again to confirm. SENDER and select a channel. Push the "M"-button again to confirm. SENDER and
RECEIVER must operate on the same channel.
LED DISPLAY OPERATIOIN / STANDBY:
A green LED display indicates that the power has been turned ON. When the
baby does not make any sound, the unit is in STAND BY MODE and a green
LED light is flashing. Red LED light indicates low batteries. .
SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL: SENSITIVITY LEVEL:
Hold down the „M"-button of the SENDER unit until the sensitivity display Hold down the „M"-button of the SENDER unit until the sensitivity display Hold down the „M"-button of the SENDER unit until the sensitivity display Hold down the „M"-button of the SENDER unit until the sensitivity display Hold down the „M"-button of the SENDER unit until the sensitivity display Hold down the „M"-button of the SENDER unit until the sensitivity display
flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the flashes. Now select the
level. The level of sensitivity increases via 3 LED-displays from left to right and level. The level of sensitivity increases via 3 LED-displays from left to right and level. The level of sensitivity increases via 3 LED-displays from left to right and level. The level of sensitivity increases via 3 LED-displays from left to right and level. The level of sensitivity increases via 3 LED-displays from left to right and level. The level of sensitivity increases via 3 LED-displays from left to right and
low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly. low to medium to high accordingly.
LED DISPLAY AND ACCUSTIC SIGNAL FOR LOW BATTERIES:
A red LED display light accompanied by an acoustic sound indicates a low battery.
Please recharge the batteries by plugging the adapter into an outlet.The BABYPHONE
is operational during the recharging process.The included batteries can be recharged
up to 500 times which is equivalent to 1.5 years of average use.
KEYCHAIN STRAP/ HANDLE:
The keychain/ strap allow you to take the unit with you inside and outside the house by attaching
the unit to your keychain or any other attachment. This allows you to monitor your baby while you
are moving around.
Baby unit/ Sender
or or or or or or or or or or or or or or or
or or or or or or or or or or or or or or or -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity -option to select your desired sensitivity
-option to -option to -option to -option to -option to -option to -option to -option to -option to -option to -option to -option to -option to -option to -option to
page 14
30.04.2008 17:46:22