Publicité
Les langues disponibles
Les langues disponibles
ESC
RCR-2CENR RADIO SYSTEM
LED Status Indicator
• The Red LED dies out when the throttle trigger is in throttle neutral zone.
• The Red LED flashes when your vehicle runs forward and it turns solid Red when you pull the throttle trigger to the full throttle endpoint.
• The Red LED flashes when your vehicle brakes and turns solid Red when you push the throttle trigger to the full brake endpoint when the "maximum
brake force" is set to 100%.
• The Red LED flashes when the vehicle runs backward and turns solid Red when you push the throttle trigger to the full brake endpoint when the
"maximum reverse force" is set to 100%.
Restore the ESC to the default values
Press and hold the SET button for over 3 seconds anytime when the throttle is at the neutral position (except during the ESC calibration and
programming) can factory reset your ESC. The Red LED flashes a long flash (the motor beeps a long beep at the same time) and then a short, single
flash that repeats indicating that you have successfully restored all the default values within your ESC. Once you power the ESC off, and then back on,
your settings will be back in the default mode.
Calibration
Press and hold
Press the
the SET button
ON/OFF
Button
Move the throttle trigger
The Red
to the neutral position and
LED flashes
press the SET button.
once and
motor emits
"Beep"
tone.
3. To set the neutral point, leave the throttle trigger at the neutral position, press the SET button. The Red LED flashes 1 time and the motor beeps 1
time to accept the neutral position.
4. Pull the throttle trigger to the full throttle position and press the SET button. The Red LED blinks 2 times and the motor beeps 2 times to accept the
full throttle endpoint.
5. Push the throttle trigger to the full brake position, press the SET button. The Red LED blinks 3 times and the motor beeps 3 times to accept the full
brake endpoint. Release the trigger back to the neutral point. (The motor can be started 3 seconds after the ESC/Radio calibration is complete)
Programming
Press and hold
Turn ON the ESC
the SET
button
The shaded options are the factory default settings which your ESC is already set to out of the box.
Programmable Item
Option 1
1. Running Mode
Fwd/Brk
2. Battery Type
LiPo
3. Cutoff Voltage
Disabled
4. Initial Start Force
0%
5. Max. Forward Force
25%
6. Max. Reverse Force
25%
7. Max. Brake Force
0%
8. Initial Brake Force
0%
9. Drag Brake
0%
10. Drag Brake Rate
Level 1
11. Neutral Range
0.02ms
12. Start Mode/Punch
Level 1
13. PWM Frequency
1K
14. BEC Voltage
6V
15. Freewheeling
Enabled
Release the
SET button
once the LED
flashes.
Pull the throttle trigger
to the end position of
forward and press the
SET button.
The Red LED
flashes
Option 2
Option 3
Option 4
Fwd/Rev/Brk
Fwd/Rev
NiMH
Auto (Low)
Auto (Medium)
Auto (High)
2%
4%
75%
50%
50%
75%
12.5%
25%
6.25%
12.5%
5%
10%
Level 2
Level 3
0.03ms
0.04ms
Level 2
Level 3
2K
4K
7.4V
Disabled
1. Turn on the transmitter, set parameters on the throttle channel like
"D/R", "EPA" and "ATL" to 100% and the throttle "TRIM" to "0". Disable
the "ABS braking function", if available on your radio.
2. Start with the transmitter on and the ESC turned off but connected to
a battery. While holding the SET button, Turn ON the ESC, then release
the SET button when you see the RED LED on the ESC start to flash
(Note: the motor beeps at the same time). (The ESC will enter the
programming mode if the SET button is not released within 3 seconds,
which will then require you to restart from step 1.)
The Red LED
flashes twice
and motor
emits
"Beep-Beep"
tone.
1. Turn on the transmitter.
2. Press and hold the set button on the ESC ON/OFF switch.
3. Turn ON the ESC.
4. Continue to hold the set button for at least 3 seconds after the Red
LED begins to flash, entering set mode. The Red LED will then flash
the number of times that corresponds with the item # you wish to
adjust. Refer to the "Item #" column of the chart to determine the
number of Red LED flashes needed.
(1 flash = Running Mode, 2 flashes = Battery Type, etc.)
Option 6
Option 5
6%
8%
10%
100%
100%
37.5%
50%
62.5%
18.75%
25%
31.25%
50%
60%
70%
Level 4
Level 5
Level 6
0.05ms
0.06ms
0.07ms
Level 4
Level 5
Level 6
8K
16K
TM
15
Push the throttle trigger
The Red LED
to the end position of
flashes three
reverse and press the
times and
SET button.
motor emits
"Beep-Beep-
Beep" tone.
Option 7
Option 8
12%
14%
87.5%
75%
37.5%
43.75%
80%
90%
Level 7
Level 8
0.08ms
0.10ms
Level 7
Level 8
Option 9
16%
100%
50%
100%
Level 9
0.12ms
Level 9
Publicité
