Confi Guration Menu - Carrier IR2-NTC Manuel D'installation

NTC - IR2
Confi guration menu
Refer to the fi gure at page 3 (Aspect and display).
With the remote control OFF press button B for at least 5 seconds
to access to the confi guration menu. "1-" is displayed: this is the
fi rst settable item of the menu. To check this itemʼs value press but-
ton B again. The default value is displayed fi rst.
Item Value
1-
Temperature units
C: Degrees C
F: Degrees F
2-
System
Co
St
3-
Set - point displaying
Ye
No
4-
Set-point value
15,16,17,18,19,20,21,
22,23,24,25,26,27,28,
29,30,31,32 ˚C
59,60,61,62,63,64,65,
66,67,68,69,70,71,72,
73,74,75,76,77,78,79,
80,81,82,83,84,85,86,
87,88,89,90 ˚F
5-
Reset step value
0;0,5;1;1,5;2 ˚C
0;1;2;3;4 ˚F
6-
Fan speed type
F
U
7-
Blind groups available
0
1
...
4
5
8-
Blind Inclination
No
Ye
To change this value, press button F or D. Press E to save the new
setting. To display and/or change another item ("2-") press button B
and repeat the steps above.
If no button is pressed within 60 seconds, the system quits the
menu automatically. No message is sent.
The confi guration menu is described in the following table:
Description
˚C -indicates that all temperatures will be displayed in
degrees C.
˚F -indicates that all temperatures will be displayed in
degrees F.
[Defaults: "C": Degrees ˚C]
Temp SP is shown thru bar graph
Temp SP is shown thru the 7 segments digits and .5 icon
[Defaults: "Co": Communicating]
The set-point value will be displayed on the IR2 lcd
The set-point value will be NOT displayed on the IR2 lcd
[Defaults: "Ye"]
[Defaults: 22 ˚C; 72 ˚F]
[Default: "0,5" ˚C; "1" ˚F]
Fixed speed
Variable fan speed
[Default: "F" 3 fi xed speeds]
There is no blind/groups to control: no icons will be
displayed
Just one blind group is available: "1" group icons will not
be illuminated
...
Four lights groups are available: "Lamp" and "4"
groups icons will be illuminated in the light menu
There is no group, but user can manage the blind
[Defaults: "0": Blinds control disabled.]
The installed blinds doesnʼt have the capability to
modify its inclination
The installed blinds has the motor able to change
its inclination.
[Default: "No" Blinds doesnʼt have the capability to
change its inclination]
E N G L I S H
Displayed
NO
NO
YES
If "System" is Co, the
set - point will be not
displayed automatically.
NO
YES
If the reset step value is
set to 0, the stand alone
mode is not available. The
IR remote control and its
display, work as in
communicating mode
NO: In case of variable fan,
the icons available are
two: HIGH speed and
AUTO mode
YES: Once the blind menu
is selected, the groups icon
will be energized on the
lcd (no icons if just one
group is selected)
"A" and "1" icons are
energized in the blind
menu. User can manage
all blinds or just one
NO
The blind inclination
feature becomes active
into the Blind Menu. No
icon point out this feature
out of the blind menu
GB - 5