Kenmore 2130 Serie Guide D'utilisation Et D'entretien page 15

First try the solutions suggested here for assistance and to possibly avoid a service call.
If you experience
Washer not performing as expected (cont.)
Washer not draining/ Check plumbing for correct drain hose
spinning, loads are installation. Drain hose extends into
still wet, or spin light standpipe farther than 4.5" (114 mm).
remains on (indicating
that the washer was
Too much detergent causing suds to
unable to pump out
slow or stop draining and spinning.
water within 10 minutes)
(cont.)
High speed spins extract more
Dry spots on load
after cycle moisture than traditional top-load
washers.
Incorrect or wrong Check for proper water supply.
wash or rinse
temperatures
Energy saving controlled
wash temperatures.
Load not rinsed Check for proper water supply.
Not using HE detergent or using too
much HE detergent.
Washer not loaded as recommended.
Heavy sand, pet hair, lint, and
Sand, pet hair, lint,
etc. on load after detergent or bleach residues may
require additional rinsing.
washing
Load is tangling
Washer not loaded as recommended.
Not cleaning or Wash load not completely
removing stains covered in water.
Added more water to washer.
Washer not loaded as recommended.
All manuals and user guides at all-guides.com
TROUBLESHOOTING
Possible causes
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening. Lower drain hose if the end is higher than 96" (2.4 m)
above the floor. Remove any clogs from drain hose.
Use only HE detergent. Always measure and follow detergent
directions for your load. To remove extra suds, select Rinse/Spin.
Do not add detergent.
The high spin speeds combined with air flow during the final spin
can cause items near the top of the load to develop dry spots
during the final spin. This is normal.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and
have both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy Star washers use cooler wash and rinse water temperatures
than previous washer. This includes cooler hot and warm washes.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water flowing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
The suds from regular detergent can keep washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions based
on load size and soil level.
The washer is less efficient at rinsing when load is tightly packed.
Load garments in loose heaps evenly around the basket wall.
The washer will not rinse well if tightly packed. Load with dry
items only.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer has started.
Add a 2nd Rinse to the selected cycle.
See "Using Your Washer" section.
Select a cycle with a slower wash action and spin speed; however,
items will be wetter than those using a higher speed spin. See the
"Cycle Guide" to match your load with the best cycle.
Load garments in loose heaps evenly around the basket wall.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
Washer senses load size and adds correct amount of water. This
is normal and necessary for clothes to move.
Added water lifts the laundry off the washplate, resulting in less
effective cleaning.
Washer is less efficient at cleaning when load is tightly packed.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Solution
15