Troubleshooting; Disposal - Samsung DSB-9601C Consignes D'utilisation

OPERATING THE RECEIVER
HDD/VCR MODE MESSAGE
- Please stop recording before power down:
This message is displayed when you press power key while recording.
- Please stop recording to see this channel:
This message is displayed when you view a channel of another transponder
while recording.
- Please stop recording to work Time-Shift:
This message is displayed when you want to make Time-Shift while recording.
- Stop recording? [OK]:
This message is displayed when you stops recording by pressing Stop key.
- There is no program in HDD:
This message is displayed when you view the play list where no file is stored.
- Delete file? [OK]:
This message is displayed when you delete a stored file.
- Select the range of cutting:
This message is displayed when no area is specified for copying with Mark key
when you attempt file copying.
- Error! Reservation time is old:
This message is displayed when recording start time of reserved recording is
earlier than the current time.
- Error! Reservation time is overlapped with the others:
This message is displayed when reserved recording time is overlapped with a
time previously reserved.
- HDD Full:
This message is displayed when there is no free space in HDD.
- HDD Format Starting:
This message is displayed when you start HDD formatting.
- HDD Format End:
This message is displayed when you complete HDD formatting.
- Require PIN code, press PLAY:
This message is displayed when you attempt playing a parental locked file.
- There is no space to record:
This message is displayed when you attempt TimeShift with HDD of free space
smaller than 10 minutes.
- Stop Time-Shift? [OK]:
This message is displayed when you press Stop key, or attempt moving a
channel or a menu during TimeShift.
GB-46
P E R S O N A L V I D E O R E C O

TROUBLESHOOTING

Problem Possible cause
No display LED on Power cord
the front panel; not plugged in correctly
No power supply
No pictures on the screen Receiver in Standby mode;
Scart not connected tightly
to video output of television;
incorrect channel or video
output selected on television
No sound Audio cord connected
incorrectly;
Loudness level = 0;
Muting active
No Audio Channel has no soundtrack
"No Video/Audio Signal" Channel has no soundtrack
Message
Remote Control does not incorrect operation;
operate directly Batteries dead or inserted
incorrectly
Poor picture quality Signal strength to low
On-Screen Error Message Antenna cable not connected
"Searching for signal" or not tight;
LNB defective;
incorrect position of the
satellite antenna;
On-Screen Error Message Satellite not yet set
"Channel data
does not exist."
Locked file does not play It is not allowed to enter PIN
in PIP mode while HDD Code for locked file in PIP
playing. mode.
No channel is displayed No channel information in a
after replacing HDD. new HDD
Recording Error No signal or weak signal
No smart card or CAM
HDD full Frequently touch
the RCU on recording

DISPOSAL

The device, packaging material (e.g. Styrofoam) and the batteries must never be
disposed of with household refuse. Please obtain appropriate information about the
regulations in your community, and dispose of all refuse in accordance with regulations
at the separate locations provided.
R D E R C O M M O N I N T E R F A
Solution of the problem
Power cord plug in correctly
Set receiver to "On";
Check connection and correct;
Check channel and video output and
correct (TV instruction manual)
Check connection and correct;
Increase loudness on television set;
Press the MUTE key or volume control
keys(Left/Right).
Press ALT key and check the soundtrack
information.
Press ALT key and check the soundtrack
information.
Point remote control
towards the Receiver.
Replace batteries or insert correctly
Check the signal strength in
the "Auto Scan" menu, correct alignment
of your antenna
Check connection and correct;
Change LNB;
Check position and correct,
Check the signal strength in
the "Auto Scan" menu
Scan of in "Automatic scanning"
or "Manual scanning" menu
Press OK key to switch to Full Screen
Play mode, and then press Play key to
display the PIN Code Input window.
Enter PIN Code and press OK key to
activate PIP mode. Any locked files will
be played.
Channel information shall be scanned
for a new HDD.
Check the cable connection
Insert the smart card or CAM
Check the HDD free size.
Do not push the RCU keys on recording
GB-47
C E