Candy CFT63W Prescriptions De Montage Et Mode D'emploi page 13

Individuals can play an important role in ensuring that WEEE
does not become an environmental issue; it is essential to
follow some basic rules:
− WEEE should not be treated as household waste;
− WEEE should be handed over to the relevant collection
points managed by the municipality or by registered
companies. In many countries, for large WEEE, home
collection could be present.
In many countries, when you buy a new appliance, the old one
may be returned to the retailer who has to collect it free of
charge on a one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as the supplied
equipment.
Appliance designed, tested and manufactured according to:
• Safety: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC
62233.
• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO
5168; EN/IEC 60704-1; EN/IEC 60704-2-13; ISO 3741; EN
50564; IEC 62301.
• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2;
EN/IEC 61000-3-2; EN/IEC 61000-3-3. Suggestions for a
correct use in order to reduce the environmental impact:
Switch ON the hood at minimum speed when you start
cooking and kept it running for few minutes after cooking is
finished. Increase the speed only in case of large amount of
smoke and vapour and use boost speed(s) only in extreme
situations. Replace the charcoal filter(s) when necessary to
maintain a good odour reduction efficiency. Clean the grease
filter(s) when necessary to maintain a good grease filter
efficiency. Use the maximum diameter of the ducting system
indicated in this manual to optimize efficiency and minimize
noise.
By placing the marking on this product, we declare,
on our own responsability, compliance to all of European
safety, health and environmental requirements stated in the
legislation for this product.
Use
The hood is designed to be used either for exhausting or filter
version.
Ducting version
The cooker hood has an upper air duct B1 and an optional
rear air duct B2*, for external fumes exit.
Select the suitable air duct and apply the flange C supplied,
ensure to close the unused hole duct with cap D* supplied if
provided.
Note: in some models upper hole B1 is supplied closed:
Press firmly to detach the detachable part that closes the
outlet hole and remove it.
Attention! The detachable part cannot be mounted in
position again. Carry out this operation only if you are sure
of the type of installation to make.
Caution! In some models the rear hole duct is not easily
accessible, even when the tap (if mounted) is removed, in this
case remove the plastic piece E1 or E2 that is blocking the
hole duct, by unwinding using pliers and cutter. Check that
the filter/suction selector (inside the cooker hood) G is in the
suction (A) position.
Filter version
In the case where it is not possible to discharge the cooking
fumes externally, the cooker hood may be used in the filter
version by fixing a carbon filter, the fumes and vapours are
recycled via the anterior grill placed above the control panel.
Check that the filter/suction selector (inside the cooker
hood) G is in the filter (F) position.
The models with no suction motor only operate in ducting
mode, and must be connected to an external suction device
(not supplied).
The connecting instructions are supplied with the peripheral
suction unit.
Installation
The minimum distance between the supporting surface for the
cooking equipment on the hob and the lowest part of the
range hood must be not less than 60cm from electric cookers
and 75cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
Electrical connection
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If provided with
a plug connect the hood to a socket in compliance with current
regulations and positioned in an accessible area, after
installation. If it not fitted with a plug (direct mains connection)
or if the plug is not located in an accessible area, after
installation, apply a double pole switch in accordance with
standards which assures the complete disconnection of the
mains under conditions relating to over-current category III, in
accordance with installation instructions.
Warning! Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that
the mains cable is correctly assembled.
Warning! If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified
persons in order to avoid hazard.
Mounting
The cooker hood may be installed on the wall or on the base
of a cabinet; if supplied, use the hole gauge H to drill the
correct distance, otherwise lean the cooker hood on the wall
or on the base of the cabinet and mark the holes with a pencil.
Wall mounting - Insert the wall screw anchors J in the drilled
holes and the two K screws in the upper drill holes, remove
the grill and hook the cooker hood to the 2 screws, finally from
the inside, insert the third screw L and lock them all in.
13