Worx WX856 Serie Notice Originale page 9

The declared vibration total value and the declared noise
emission value have been measured in accordance with a
standard test method and may be used for comparing one
tool with another.
The declared vibration total value and the declared
noise emission value may also be used in a preliminary
assessment of exposure.
WARNING: The vibration and noise emissions
during actual use of the power tool can differ from
the declared value depending on the ways in which the
tool is used especially what kind of workpiece is processed
dependant on the following examples and other variations
on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
The use of the correct accessory for the tool and ensuring it
is sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration and noise accessories are used.
And the tool is being used as intended by its design and
these instructions.
This tool may cause hand-arm vibration syndrome if
its use is not adequately managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use should
also take account of all parts of the operating cycle such
as the times when the tool is switched off and when it
is running idle but not actually doing the job. This may
significantly reduce the exposure level over the total
working period.
Helping to minimise your vibration and noise exposure risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and
keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti vibration
and noise accessories.
Plan your work schedule to spread any high vibration tool
use across a number of days.
Category Model
WA3550
WA3550.1
20V Battery WA3551
WA3551.1
WA3553
WA3760
20V Charger WA3869
WA3880
We recommend that you purchase your accessories
from the same store that sold you the tool. Refer to
the accessory packaging for further details. Store
personnel can assist you and offer advice.
20V Cordless Orbital Buffer
OPERATING INSTRUCTIONS
INTENDED USE
The machine is intended for polishing floor, car and
other coated surfaces.
1. INSTALL/REMOVE THE BATTERY PACK
To install: Place the switch in the OFF (O) position.
Then, slide the battery pack into the polisher. (See
Fig. A1)
To remove: Place the switch in the OFF (O) position.
Then, press the button to remove the battery pack
from the polisher. (See Fig. A3)
Charge the battery pack. (See Fig. A2)
2. ON/OFF SWITCH (SEE FIG. B)
Always start and stop the polisher against the car
surface.
3. ATTACHING THE APPLICATOR BONNET TO
THE FOAM PAD (SEE FIG. C)
Place the switch in the OFF (O) position. Remove
the battery pack from the tool. Place the terry cloth
bonnet securely over the foam pad.
4. SPREAD THE POLISH
Spread about a tablespoonful of polish evenly over
the entire surface of the pad cover. Do not apply
polish directly to car.
Application of paste polish (See Fig. D1)
Do not apply paste directly to the surface being
polished. Spread the paste evenly over the entire
surface of the bonnet.
Application of liquid polish (See Fig. D2)
Apply approximately half- dollar size of liquid around
the center of the bonnet, followed by two more rings,
each slightly larger than the previous one.
Capacity
NOTE: Be careful not to use too much polish at one
time, otherwise it will be more difficult to remove the
1.5Ah
polish later.
1.5Ah
5. TO USE THE CAR POLISHER
2.0Ah
When the polisher is firmly positioned on the
surface. Always start and stop the polisher on or
2.0Ah
against the surface being polished. Start by polishing
4.0Ah
larger flat surfaces, such as the hood, trunk and roof.
After covering a flat surface, polish curved surfaces
0.4A
such as car doors and mudguards. Do not use a
polisher to press the surface down. Turn the polisher
2.0A
off before you remove it from the surface. (See Fig.
2.0A
E1)
NOTE: It is also convenient to use one hand to polish
the roof and car sides. (See Fig. E2)
NOTE:For hard to reach areas, such as the underside
of bumpers or side mirrors, apply polish by hand.
(See Fig. E3)
6. CHANGE TO BUFFING/POLISHING BONNET
TO THE FOAM PAD (SEE FIG. F)
NOTE: Before using the tool, read the
instruction book carefully.
9
EN