Publicité
Les langues disponibles
Les langues disponibles
Fax +32 030 9904733
• Position the fan heater far from other sources of heat, inflammable materials (curtains, carpets,
etc.), inflammable gases or explosive materials (spray cans) and from materials that can deform on
exposure to heat. Make sure that there is 100 cm of free space in front of the fan heater and 30 cm
on the sides. Do not use the heater in the immediate vicinity of a bathtub, shower or swimming
pool (to avoid drops of water falling on the heater or the heater falling in the water), or in places
where it could be subject to shocks.
• Do not hang or simply pull the unit to the wall or walls.
• Make sure that the fan heater is working correctly: if not, turn the heater off and have it checked by
professionally qualified personnel.
• Make sure that the air-intake grid is not obstructed by objects, fabrics or anything else to avoid the
heater overheating or breaking.
• Do not use the appliance with a timer or a programmer or with a system that can switch on the
appliance automatically, to avoid risk of fire, since a fire risk exists if the heater is covered or
positioned incorrectly. Check that no other high absorption appliances are connected to the same
power source.
• In the case of a breakdown or fault, switch off the appliance and have it checked by a
professionally qualified technician; repairs made by unqualified persons can be dangerous and
render void the warranty.
USE
Before each use, verify that the unit is in good condition, the electric cord is not damaged, if the
power cord is damaged, it must be replaced by the manufacturer or a competent qualified electrician
or a person with similar qualifications, in order to avoid any risk.
mod. S337 basic version (Fig.1)
The fan-heater is fitted with switch, thermostat:
- the switch sets following functions:
"0"= OFF; "
"= fan; "I"= = air warm (1000W); "I I"= air very hot (2000W)
- the thermostat sets the room temperature, that will be higher if the knob is rotated to position max
clockwise: when the temperature is reached, it will be kept uniform
To use the thermofan, please follow the instructions below:
1)
Insert the plug in the current socket.
2)
Turn the thermostat knob (A) clockwise to the position corresponding to the desired temperature.
3)
To switch the appliance on, turn the selector knob (B) to the position corresponding to the
desired function; the pilot light comes on in the following functions "
the presence of voltage.
4)
To turn off the fan heater, please turn the Knob in the "0" position and the thermostat knob
anticlockwise. Then pull out the plug from the socket.
Never leave the appliance connected to the socket if it is not in use, especially for long periods.
mod. S339 version left-right oscillation (Fig.2)
The fan-heater is fitted with switch, thermostat, left-right oscillation:
- the switch sets following functions:
"0"= OFF; "
"= fan; "I"= = air warm (1000W); "I I"= air very hot (2000W)
- the thermostat sets the room temperature, that will be higher if the knob is rotated to position max
clockwise: when the temperature is reached, it will be kept uniform
- left-right oscillation: switch on the key for the swinging (C) to let the stove swing to the left and to
the right.
To use the fan heater, please follow the instructions below:
1)
Insert the plug in the current socket.
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
8
17
/
Assembly page 8/17
"-"I"-"II", indicating
Publicité
