Bimar Funny Notice D'instructions page 7

Fax +32 030 9904733
• Ensure that the heating fan does not come into contact with water or other liquids. If this should
happen, never immerse hands in the liquid but remove the plug from the socket first of all. Dry the
appliance carefully and check that all the electric parts are dry. If in doubt, call a qualified expert.
• If the appliance should fall over or shows signs of faulty operation, disconnect the electrical cable
immediately. Check that no part is damaged and switch it on after the appliance has been
thoroughly checked: in case of doubt, contact qualified professional personnel.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.
• The appliance must be kept out of children's reach.
• Attention: when using electric appliances, the basic safety precautions must always be
observed to avoid risks of fire, electric shocks and physical injury.
• Unplug the appliance when not in use.
• The fireguard of this heater is intended to prevent direct access to heating elements and must
be in place when the heater is in use, but the fireguard does not give full protection for young
children and for infirm person.
• Do not move the appliance when it is in function.
• That the user must not leave the appliance unattended while it is connected to the supply.
• Do not touch the heater with wet hands or feet.
• Never use the radiator to dry damp garments.
• Do not expose the heater to the weather (sun, rain, etc.).
• Do not pull on the power cord or the appliance to unplug the appliance from the wall socket. Never
move the appliance by pulling the cord.
• If the electric cord is damaged, it has to be replaced by the supplier or an authorized service center
or a professionally qualified, to avoid any risks.
This symbol show: ATTENTION do not cover the appliance when it is operating to
avoid the risk of fires.
INSTALLATION
• After removing the packing materials, check the integrity of the heater; if you are unsure, do not
use it and ask for qualified professional help. The packing materials (plastic bags, polystyrene
foam, nails, etc.) must be kept out the reach of children because they are potential sources of
danger.
• Before connecting the appliance, check that the voltage shown on the data plate matches that of
your electricity (230V~ 50Hz) and that the electric plug is grounded. In the event of incompatibility
between the electric outlet and the plug of the heater, have the outlet replaced with another more
suitable type by professionally qualified personnel, who will make sure that the section of the wires
of the outlet is appropriate for the absorbed power of the heater (10A). Check that the mains are not
connected equipment; high absorption to prevent overloading and fire risks. In general, the use of
adapters or extension cords is not recommended; if their use is indispensable, they must conform to
existing safety standards and their current capacity (amperes) must not be less that the maximum of
the heater.
Attention: before use the appliance remove the detachable coupon to stick the handle.
• Before each use, verify that the heater is in good condition and that the electrical cord is not
damaged: in the case of doubt, ask for professionally qualified help.
• Make sure that the cable is correctly positioned and that it is not in contact with hot parts or sharp
edges, nor wrapped around the device or twisted.
• The power socket must be easy to reach so the plug can be removed quickly in case of emergency.
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
7 17
/
Assembly page 7/17