Description (Fig. 1); Switching On/Off - Ryobi ERH-650V Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
GB
FR
DE
ES
IT
SPECIFICATION
ERH-750V(230V) ERH-750V(110V)
- concrete / stone
24 mm
Tool attachment
SDS-plus
Weight
3.20 kg

DESCRIPTION (FIG. 1)

1.
Locking Collar
2.
Variable switch with reverse action
3.
Lock-on button
4.
Auxiliary handle
5.
Depth stop
6.
Mode selector
7.
Live tool indicator
BEFORE STARTING TO USE YOUR HAMMER
DRILL
Examine the place where the tool is to be used for
hidden electrical cables, gas, and water pipes using a
pipe finding device.
Before you plug in your tool, make sure that the
supply voltage used corresponds to that indicated on
the rating plate.
FITTING AND CHANGING BITS (FIG. 2)
The device is equipped with an SDS-plus attachment
system.
Clean the bit and grease it with a thin layer of
machine grease before inserting it into the chuck.
Pull back the locking collar (A.) and hold it.
Push and rotate the dust-free tool into the bit holder
as far as it will go.
Release the locking collar to lock the bit.
Check that it has locked by pulling on it.
REMOVING THE BIT FROM THE SDS-PLUS
SYSTEM
Pull back the Locking collar (A) and remove the bit.

SWITCHING ON/OFF

Speed control
The speed of the drill may be varied by increasing the
pressure exerted on the trigger (2). The speed will
increase as more pressure is applied.
ERH-650V&ERH-750V 24lag-ok.indd Sec1:2
ERH-650V&ERH-750V 24lag-ok.indd Sec1:2
NL
PT
DK
SE
FI
NO
English
24 mm
SDS-plus
3.20 kg
RU
PL
CZ
HU
RO
LV
To limit the maximum speed of the drill, rotate the dial
on the front of the trigger until the desired setting is
achieved.
Lock-on button
If you want to keep your hammer drill operating at a
constant speed, press the lock-on button (3) while
pressing the variable switch. To unlock this function,
briefly press the variable switch (2) then release it.
AUXILIARY HANDLE (FIG. 4)
For reasons of safety, only use the hammer drill when it is
fitted with the auxiliary handle.
To loosen the auxiliary handle, rotate the handle
anticlockwise until the handle assy is free to move.
Position the handle as required then lock securely by
rotating the handle clockwise until it is tight.
DEPTH STOP (FIG. 5)
Fit the depth stop. Loosen wing bolt D to adjust the depth
stop. The depth of the hole drilled will be equal to the
distance between the end of the drill bit and the front end
of the depth stop.
MODE SELECTOR (FIG. 6)
Your hammer drill is equipped with a hammer stop facility
for smooth drilling.
To deactivate the hammer action, turn the mode
selector (6) clockwise to "
To reactivate the hammer action, the mode selector
(6) has to be reset to "
You can use the selector to change modes even when
the hammer drill is operating (at low speed). The selected
mode is only activated once the variable switch (2) is
pressed to start the tool.
Note:
Anti-clockwise rotation during impact drilling
damages the drill bit. Deactivate the hammer
action when using a diamond drill bit.
ROTATION STOP (FOR ERH-750V ONLY)
The mode selector on the ERH-750V features a third
position, Rotation Stop Mode "
rotation of the tool whilst maintaining the hammer action.
This feature enables the tool to be used for chiselling,
when fitted with the appropriate bit.
2
LT
EE
HR
SI
SK
GR
".
".
",which stops the
6/24/09 6:01:32 PM
6/24/09 6:01:32 PM
TR

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Erh-750v

Table des Matières