Publicité
Les langues disponibles
Les langues disponibles
THIS APPLIANCE IS CONCEIVED FOR DOMESTIC USE
ONLY. THE MANUFACTURER SHALL NOT IN ANY WAY BE
HELD RESPONSIBLE FOR WHATEVER INJURIES OR
DAMAGES ARE CAUSED BY INCORRECT INSTALLATION OR
BY UNSUITABLE, WRONG OR ABSURD USE.
The manufacturer declares that this product meets all the
essential requirements for low voltage electrical material set
out in European directive 2006/95/EEC of 12 December 2006
and for electromagnetic compatibility as required by
European directive 2004/108/EEC of 15 December 2004.
User's Instructions
Installation
All operations relative to installation (electric connection)
should be carried out by skilled personnel in conformity with
the rules in force.
As for the specific instructions see part pertaining to
installer.
Use
TOUCH CONTROL HEATING ELEMENTS
Touch sensitive keys
All operations can be performed using touch sensitive keys
(capacitive sensors) located on the front of the control
board; each key has a corresponding display. All actions are
confirmed by an audible signal.
TOUCH CONTROL B (Fig. 2)
1 Power ON / Power OFF
2 Cooking zone +
3 Cooking zone –
4 Double circuit
5 Timer
6 Setting display
7 Timer display
8 Zone selection lights
9 Timer indicator light
Switching the Touch Control ON/OFF
After mains voltage is applied the control initializes for
approx. 1 second before it is ready for operation. After a
reset all displays and LEDs glow for approx. 1 second. When
this time is over all displays and LEDs extinguish and the
control is in the stand-by mode.
By operating the ON/OFF key the control can be turned into
the ON-mode. The cooking zone displays show a static "0".
If a cooking zone is in the "hot" status, the display shows a
static "H" instead of "0". The bottom right dot is blinking in
1 second intervals on all cooking zone displays to indicate
that no cooking zone is selected at the moment.
After switching-ON the electronic control remains activated
for 20 seconds. If no cooking zone or timer selection follows
within this period of time, the electronic control
automatically switches back into the stand-by-mode.
The control can only be switched-ON if it identifies the
ON/OFF key alone being operated. Should it recognize key
activation other than that, the control remains in the
standby- mode.
If the child safety feature is active when switching on, all
cooking zones show "L", (LOCKED). (also refer to 1.11). If
the cooking zones are in a "hot" status, the display shows
"L" and "H" in alternation. When the Touch Control is ON it
can be switched-
OFF at any time by operating the ON/OFF key. This is also
valid if the control has been locked (activated child safety
feature).
The ON/OFF key has always priority in the switch-OFF
function.
Automatic switch-OFF
When the control is ON it automatically switches-OFF after
20 seconds if no cooking zone or select key has been
operated within this period of time. If case of a cooking zone
selection, the automatic switch- OFF time is composed of 10
seconds deselection time for a cooking zone at setting"0"
and 10 seconds switch-OFF time.
Switching a cooking zone ON and OFF
If the control is ON the respective cooking zone can be
selected by operating a cooking-zone-select-key (= PLUS-
key of the respective cooking zone). There is a static dot
indication in the respective display. If the cooking zone is
"hot "0" is displayed instead of "H" . On all other cooking
zone displays the blinking dot extinguishes. Then a setting
will be chosen by a renewed operation of the cooking- zone
select- key or the MINUS-key and the cooking zone begins to
heat up. In order to use the cooking-zone-select-key as a
PLUS-key the control has to recognize that after the
selection the cooking zone has been released for 0,3
seconds.
After selection of a cooking zone the setting can be
increased by continuously pressing the PLUS-key, starting at
step "1" it is increased by 1 step every 0,4 seconds. When
setting "9" is reached the setting will not be changed further
(end stop).
If the selected cooking zone will be switched ON by means
of the MINUS key, the cooking zone starts at the maximum
setting "9" ("reverse switching-ON").
When the key is continuously operated, it decreases by 1
step every 0,4 seconds. When setting "0" is reached, there
will be no further setting changed (end stop). Only a
renewed operation of the MINUS (or PLUS) key changes the
setting.
Switching OFF an individual cooking zone
To switch off an individual cooking zone, the respective
cooking zone has to be selected with the cooking-zone-
select key (= PLUS). The selection is indicated with the static
dot in the respective cooking zone display. If the control
recognizes that the PLUS- (cooking-zone-select-key is the
PLUS-key) and the MINUS key have been activated
simultaneously the setting of the selected cooking zone will
be put back to "0". Alternatively, the MINUS-key can be used
to count down the setting to "0". If all cooking zones are at
"0", all decimal points in the cooking zone displays are
blinking. If a cooking zone is "hot", "H" will be displayed
instead of "0".
Switching-OFF all cooking zones
Publicité
