Bosch EasyDrill 1200 Notice Originale page 13

Intended use
The power tool is intended for driving and loosening screws
and for drilling in wood, metal, ceramic and plastic.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Keyless chuck
(2) Front sleeve
(3) Rear sleeve
(4) Torque presetting ring
(5) Gear selector switch
(6) Clockwise rotational direction indicator
(7) Anti-clockwise rotational direction indicator
a)
(8) Battery release button
a)
(9) Battery
(10) Rotational direction switch
(11) On/off switch
(12) "PowerLight"
(13) Handle (insulated gripping surface)
a)
(14) Screwdriver bit
a)
(15) Universal bit holder
(16) Securing screw for keyless chuck
b)
(17) Hex key
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
b) Commercially available (not included in the scope of deliv-
ery)
Technical Data
Cordless drill/driver
Article number
Rated voltage
A)
No-load speed
– First gear
– Second gear
Max. torque, hard/soft
screwdriving application ac-
A)
cording to ISO 5393
Max. drilling diameter
– Steel
– Wood
Max. screw diameter
Chuck capacity
Drill spindle thread
Weight according to
B)
EPTA-Procedure 01:2014
Bosch Power Tools
Cordless drill/driver
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20−25 °C with rechargeable battery PBA 12V
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Noise/vibration information
Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted sound pressure level of the power
tool is 71 dB(A). Uncertainty K=3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection
Vibration total values a
determined according to EN 62841-2-1:
Drilling in metal: a
Screwdriving: a
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
EasyDrill 1200
plication tools or is poorly maintained, the vibration level
3 603 JA2 1..
and noise emission value may differ. This may significantly
V= 12
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
-1
min 0–450
times when the tool is switched off or when it is running but
-1
min 0–1650
not actually being used should also be taken into account.
Nm 20/11
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
mm 6
and organising workflows correctly.
mm 20
mm 6
Assembly
mm 0.8–10
Removing the battery (see figure A)
3/8"
kg 1.0
u
C)
and
1.5Ah .
(triax vector sum) and uncertainty K
h
2
< 2.5 m/s , K = 1.5 m/s
h
2
< 2.5 m/s , K = 1.5 m/s
h
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
1 609 92A 6DH | (26.05.2021)
English | 13
EasyDrill 1200
°C 0 to +35
°C –20 to +50
PBA 12V...
AL 11..CV
GAL 1110 CV
GAL 12...
2
2