Bosch EasyHammer 12V Notice Originale page 16

16 | English
Setting the Operating Mode
You can set the required operating mode using the mode se-
lector switch (4). To do this, set the switch to the relevant
operating mode.
Symbol Operating mode
R = anticlockwise rotation
Drilling/Screwdriving
Hammer drilling
Switching On and Off
– To switch on the power tool, press the on/off switch (5).
The worklight (10) lights up when the on/off switch (5) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
– To switch off the power tool, release the on/off switch
(5).
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
Adjusting the Speed/Impact Rate
– Adjust the speed/impact rate of the power tool when it is
on by pressing in the on/off switch (5) to varying extents.
Applying light pressure to the on/off switch (5) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
Practical Advice
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
Maintenance and Service
Maintenance and Cleaning
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
If the battery is no longer working, please contact an author-
ised after-sales service agent for Bosch power tools.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Replace a damaged dust protection cap immediately.
u
It is recommended that you have use an after-sales
service for this.
1 609 92A 4MK | (28.01.2021)
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The contained lithium-ion batteries are subject to the Dan-
gerous Goods Legislation requirements. The batteries are
suitable for road-transport by the user without further re-
strictions.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Disposal
Power tools, rechargeable batteries, accessor-
ies and packaging should be sorted for environ-
mental-friendly recycling.
Do not dispose of power tools and batteries/re-
chargeable batteries into household waste!
Only for EU countries:
According to the Directive 2012/19/EU, power tools that
are no longer usable, and according to the Directive
2006/66/EC, defective or used battery packs/batteries,
must be collected separately and disposed of in an environ-
mentally correct manner.
Battery packs/batteries:
Li-ion:
Please observe the notes in the section on transport (see
"Transport", page 16).
Bosch Power Tools