GYM form SLIM FOLD TREADMILL PRO Mode D'emploi page 16

SIDES AND THAT
PINS ARE COMPLETELY INSERTED.
FAILURE TO DO SO COULD MAKE
THE TREADMILL UNSTABLE AND MAY
CAUSE INJURY.
Check the angle of incline of each level
on the Table of Incline Positions in the
first section of this manual.
Unfolding the device (see Picture 9)
1. Hold onto the base (3) with one hand
and use the other to pull out the vertical
bar screw (5) and unlock the base.
2. Slowly lower the base (3) until it is on
the floor.
3. Firmly tighten the lock screw (7).
4. Remove the two handlebar screws
(26).
5. Lower the handlebars (6) to the
horizontal position.
6. Attach the two handlebar screws (26).
Folding up the device (see Picture 10)
1. Remove the two handlebar screws
(26).
2. Raise the handlebars (6) to the vertical
position.
3. Replace the two handlebar screws
(26) so they are not lost.
4. Loosen the lock screw (7).
5. Raise the base to the vertical position
and hold it in place.
6. Attach the base (3) to the vertical bars
(17) with the vertical bar screw (5).
When the device is folded, it can be
transported using the wheels (16).
Product Cleaning and Maintenance
• Before performing
make sure the device is off by pressing
the ON/OFF button and pulling the plug
from the power supply.
• Do not use abrasive products or
solvents to clean the device.
• Remove any dirt from the device with a
damp cloth.
• Use a dry cloth to clean the plug and
control panel. Do not use a damp cloth.
• Do not use the device in very damp or
16
THE INCLINE dusty places that could cause the device
to fail. Set up the device on a flat surface
to prevent it from falling and breaking
down.
• Do not use the device for more than
an hour. Rest for an hour after each one-
hour workout. The components should
be kept clean. Both sides of the belt
should be cleaned to reduce dirt build-
up. Before using the device, make sure
the treadmill surface is clean. Use soap
and a damp cloth to clean the belt. Do not
use solvents. Wipe off the sweat on the
handlebars after each use.
• Anti-static lubricant was applied to the
belt at the factory.
• Lubricant can be applied to the
device after 100 hours of use. Apply a
special treadmill lubricant underneath
the treadmill belt by lifting the belt away
from the base slightly and applying the
lubricant.
Centring the belt:
IMPORTANT: After continuous use, the
belt may shift to one side due to the
constant pressure of the feet. It should
be centred again by adjusting the belt
screws (29) with the Allen key provided
(15). See Picture 11.
Each time you are going to use the
treadmill, make sure the belt is centred
between the screws on the base. Centre
it if necessary. It usually requires only
minor adjustments. On the side the belt
has shifted towards, tighten the screw
half a turn clockwise and then test the
treadmill for at least 15 seconds at 4
km/h. Make sure shifting has been
corrected and, if necessary, tighten the
daily cleaning, screw ¼ or half of a turn more until the
belt is centred.
NOTE: Check the distance between the
belt and the edge of the treadmill. If it
looks like the belt in Picture 12, it needs
to be centred.
Tightening the belt: (Fig.13):
3. If the treadmill belt (4) slides during
use, it should be tightened. Switch OFF
the treadmill and unplug it from the power
source. Use the Allen key (15) to give the
left screws and then the right screws ¼ of
a turn in the clockwise direction. Switch
ON the main switch and start the treadmill
running at 6 km/h. Walk on the treadmill.
If it still slides, repeat the process until
the belt no longer slides.
- If you do not plan to use the device for
an extended period of time, please store
it in a clean, dry place and prevent it from
coming into contact with dust.
• Do not touch the ON/OFF button or the
power cable with wet hands.
• Do not tug on the cable when
unplugging the device. To prevent the
cable from being damaged, do not place
heavy objects on top of it and do not
wrap it around the device . Do not use
the device if the cable or the plug do not
make a good connection.
NOTE: The belt should not be too tight
because the device could damage it
during operation and make noise.
Technical Specifications:
Voltage: 220-240 V
Frequency: 50/60 Hz
Power : 735W
Assembled size: 1575mm x 680mm x
1188mm (L x W x H)
Folded size: 472mm x 680mm x 1505mm
(L x W x H)
Packaging size: 1610 mm x 700 mm x
290 mm (L x W x H)
Net Weight 32 kg
Gross Weight 36 kg
Class HB product for household use
Gymform Slim Fold Treadmill
(VDPGYCIND0121)
DISPOSAL OF MATERIALS
A symbol of a crossed-out wheeled
bin means you should find out about
and follow local regulations about
disposing of this kind of product.
Pro