Alpine TME-M760 Mode D'emploi

TME-M760
6.5-INCH WIDE LCD COLOR MONITOR
OWNER'S MANUAL
Please read before using this equipment.
MODE D'EMPLOI
Veuillez lire ce mode d'emploi avant la mise en service de l'appareil.
MANUAL DEL PROPIETARIO
Por favor, léalo antes de utilizar este equipo.
All manuals and user guides at all-guides.com
R
68P20877Y74-A
R
Printed in China (S)
Points to Observe for Safe Usage
WARNING
This symbol means important instructions.
Failure to heed them can result in serious injury or death.
DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN. Swallowing them may result in
serious injury. If swallowed, consult a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure.) Failure to do so
may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL. Failure to do so may result in
electric shock or injury due to electrical shorts.
DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply power to other equipment. Doing
so will exceed the current carrying capacity of the wire and result in fire or electric shock.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR
GEARSHIFT. Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or
nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the
vehicle in a safe location before performing these functions. Failure to do so may result in an accident.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and cables in
compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as
the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precau-
tions may result in fire.
MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING. Failure to do so may
result in an accident.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may result in fire,
electric shock or other injury.
DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG. If the unit is not installed correctly the air bag
may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and
injuries.
MINIMIZE DISPLAY VIEWING WHILE DRIVING. Viewing the display may distract the driver from looking ahead of the vehicle
and cause an accident.
DO NOT WATCH VIDEO WHILE DRIVING. Watching the video may distract the driver from looking ahead of the vehicle and
cause an accident.
INSTALL THE PRODUCT CORRECTLY SO THAT THE DRIVER CANNOT WATCH TV/VIDEO UNLESS THE VEHICLE IS
STOPPED AND THE EMERGENCY BRAKE IS APPLIED. It is dangerous (and illegal in many states) for the driver to watch
TV/Video while driving a vehicle. Installing this product incorrectly enables the driver to watch TV/Video while driving. This may
cause a distraction, preventing the driver from looking ahead, thus causing an accident. The driver or other people could be
severely injured.
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or material property damage.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the cables and wiring
away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If
wiring passes through a hole in metal, use a rubber grommet to prevent the wire's insulation from being cut by the metal edge
of the hole.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified accessory parts.
Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause
parts to become loose resulting in hazards or product failure.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high
incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technica
skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product.
Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing.
Operation
Screen Display ON/OFF
1 Press the PWR button.
2 To turn off the POWER, press the PWR button again.
Note:
If properly connected, the monitors main POWER will turn off when the vehicle's ignition switch is off. If the main power
lamp illuminates in the STAND BY mode, the vehicle's battery may be discharged.
Adjusting the Volume
1 Adjust the volume level by pressing the DN
Switching NTSC/PAL
Switch the movie output type NTSC/PAL in AUX1, AUX2 and/or AUX3 mode.
1 Press the DISP button for at least 1 second.
Note: When the movie output type is not compatible, the movie does not output normally.
Switching the source
1 Press the SELECT button. Each press of the button will cycle through the modes as follows:
NAVIGATION AUX1 AUX2
Switching the display mode.
English
or UP button.
AUX3